Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100612 SEAT BELT _0467501 SEAT BELT WARNING SYSTEM U

SEAT BELT  SEAT BELT WARNING SYSTEM  TERMINALS OF ECU  


CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E444785C14
3.438,7.698 3.833,8 0.396,0.302 5.438,3.26 5.854,3.5 0.417,0.24 1.333,3.25 1.75,3.49 0.417,0.24 1.417,4.51 1.833,4.75 0.417,0.24 1.083,6.094 1.5,6.333 0.417,0.24 3,6.083 3.417,6.323 0.417,0.24 3.833,4.5 4.25,4.74 0.417,0.24 6.25,6.083 6.667,6.323 0.417,0.24 4.25,6.094 4.667,6.333 0.417,0.24 5.688,4.5 6.104,4.74 0.417,0.24 5.25,6.094 5.667,6.333 0.417,0.24 3.417,3.25 3.833,3.49 0.417,0.24 1.917,0.698 1.917,0.479 1.917,0.479 2.083,0.479 true 0.719,1.167 1,1.167 true 1.927,1.25 2.167,1.25 true 1.927,1.552 2.167,1.552 true 0.75,1.958 0.99,1.958 true 0.76,2.229 1,2.229 true 0.75,2.469 1.229,2.469 true 0.719,1.667 1,1.667 true 6.167,1.208 6.448,1.208 true 6.167,1.771 6.448,1.771 true 6.167,2.167 6.448,2.167 true 1.927,1.875 2.167,1.875 true 1.25,0.5 1.25,0.281 1.25,0.281 1.417,0.281 true 4.5,0.583 4.5,0.365 4.5,0.365 4.667,0.365 true 6,0.531 6,0.313 6,0.313 6.167,0.313 true 3.927,1 4.083,1.198 0.156,0.198 10 false A 3.594,7.76 3.75,7.958 0.156,0.198 10 false A 0.521,1.583 0.833,1.781 0.313,0.198 10 false 5E 0.521,1.885 0.833,2.083 0.313,0.198 10 false 5K 2.208,1.167 2.667,1.365 0.458,0.198 10 false I1 2.208,1.469 2.667,1.667 0.458,0.198 10 false I2 0.552,2.156 1.052,2.385 0.5,0.229 10 false 5J 2.125,0.385 2.583,0.583 0.458,0.198 10 false *2 6.521,1.135 6.833,1.333 0.313,0.198 10 false 5C 6.521,1.688 6.833,1.885 0.313,0.198 10 false 5B 1.5,3.292 1.958,3.49 0.458,0.198 10 false I3 3.594,3.292 4.052,3.49 0.458,0.198 10 false I2 1.563,4.552 1.875,4.75 0.313,0.198 10 false 5C 3.979,4.552 4.292,4.75 0.313,0.198 10 false 5B 1.229,6.146 1.542,6.344 0.313,0.198 10 false 5F 3.135,6.125 3.448,6.323 0.313,0.198 10 false 5E 6.385,6.135 6.698,6.333 0.313,0.198 10 false 5H 4.385,6.135 4.74,6.292 0.354,0.156 10 false 5K 0.521,1.094 1.135,1.292 0.615,0.198 10 false 5F 0.521,2.396 1.021,2.625 0.5,0.229 10 false 5H 6.521,2.083 6.833,2.281 0.313,0.198 10 false 5A 5.823,4.542 6.135,4.74 0.313,0.198 10 false 5A 5.406,6.135 5.719,6.333 0.313,0.198 10 false 5J 2.208,1.802 2.667,2 0.458,0.198 10 false I3 5.604,3.302 6.063,3.5 0.458,0.198 10 false I1 1.458,0.219 1.917,0.417 0.458,0.198 10 false *1 4.708,0.302 5.167,0.5 0.458,0.198 10 false *1 6.219,0.25 6.677,0.448 0.458,0.198 10 false *1
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


b.

Reconnect the power distribution box assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A-26 (BECU) - Body ground Battery power supply Always 11 to 14 V
A-27 (IGR) - Body ground Ignition power supply (IG signal) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A-13 (GND1) - Body ground Ground Always Below 1 Ω


d.

Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION


e.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
5F-26 (LCTY) - Body ground* Rear door courtesy light switch assembly LH input Rear door LH open Below 1 V
Rear door LH closed 4.7 to 5.3 V
5F-1 (RCTY) - Body ground* Rear door courtesy light switch assembly RH input Rear door RH open Below 1 V
Rear door RH closed 4.7 to 5.3 V
5F-4 - Body ground* Rear center seat belt buckle switch signal Rear center seat belt fastened 11 to 14 V
Rear center seat belt not fastened Below 1 V
5F-8 - Body ground* Rear RH seat belt buckle switch signal Rear RH seat belt fastened 11 to 14 V
Rear RH seat belt not fastened Below 1 V
5F-11 - Body ground Front passenger side seat belt buckle switch signal Front passenger side seat belt fastened 11 to 14 V
Front passenger side seat belt not fastened Below 1 V
5F-19 - Body ground* Rear LH seat belt buckle switch signal Rear LH seat belt fastened 11 to 14 V
Rear LH seat belt not fastened Below 1 V
5F-29 - Body ground Passenger seat occupant detection sensor signal Ignition switch ON, front passenger seat occupied Below 1 V
Ignition switch ON, front passenger seat not occupied 11 to 14 V

*: w/ Rear Seat Belt Warning




CHECK COMBINATION METER ASSEMBLY


E391347N13
1.5,0.667 1.917,0.917 0.417,0.25 5.167,0.667 5.583,0.917 0.417,0.25 1.646,0.719 2.104,0.917 0.458,0.198 10 false I5 5.333,0.719 5.792,0.917 0.458,0.198 10 false I6

a.

Disconnect the I5 combination meter assembly connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
I5-5 (B) - Body ground Battery power supply Always 11 to 14 V
I5-6 (IG+) - Body ground Ignition power supply (IG signal) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
I5-1 (EP) - Body ground Ground Always Below 1 Ω


c.

Connect the I5 combination meter assembly connectors.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
I6-23 (BKL) - Body ground Driver seat belt buckle switch signal Driver seat belt fastened 11 to 14 V
Driver seat belt unfastened Below 1 V
I6-7 (RRBT) - Body ground* Rear No. 2 RH seat belt buckle switch signal Rear No. 2 RH seat belt fastened 11 to 14 V
Rear No. 2 RH seat belt not fastened Below 1 V
I6-24 (RLBT) - Body ground* Rear No. 2 LH seat belt buckle switch signal Rear No. 2 LH seat belt fastened 11 to 14 V
Rear No. 2 LH seat belt not fastened Below 1 V

*: w/ Rear No. 2 Seat Belt Warning