Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the combination meter assembly. This circuit provides two types of power sources; one is a constant power source, and the other is an IG power source.

WIRING DIAGRAM

C408706E09
5.167,4.104 7.156,4.688 1.99,0.583 10 false Combination Meter Assembly 5.198,3.875 5.656,4.073 0.458,0.198 10 false I5 1.781,2.313 5.146,2.51 3.365,0.198 10 false from Battery 1.146,0.448 4.052,0.646 2.906,0.198 10 false from IGR-NO.1 Relay*2 3.125,0.667 4.094,0.875 0.969,0.208 10 false METER-IGR*2 5.563,3.073 5.875,3.271 0.313,0.198 10 false ET 5.333,2.938 5.646,3.135 0.313,0.198 10 false 2 5.573,0.313 6.031,0.51 0.458,0.198 10 false IG+ 5.313,0.313 5.625,0.51 0.313,0.198 10 false 6 5.333,2.167 5.646,2.365 0.313,0.198 10 false 5 5.552,2.156 5.708,2.354 0.156,0.198 10 false B 5.573,3.573 6.49,3.906 0.917,0.333 10 false EP 5.323,3.427 5.635,3.625 0.313,0.198 10 false 1 3.219,2.49 4.594,2.688 1.375,0.198 10 false METER 0.438,1.375 3.552,1.938 3.115,0.563 10 false from Engine Stop and Start ECU*1 4.208,0.313 5.583,0.51 1.375,0.198 10 false *2 4.74,0.74 6.115,0.938 1.375,0.198 10 false *1 0.323,3.656 3.438,4.219 3.115,0.563 10 false *2: w/o Stop and Start System 0.333,3.198 3.448,3.76 3.115,0.563 10 false *1: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

When the combination meter assembly is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the I5 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-1 (EP) - Body ground Always Below 1 Ω
I5-2 (ET) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-6 (IG+) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
I5-5 (B) - Body ground Always 11 to 14 V


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (IG+ terminal) (w/ Stop and Start System) B
NG (IG+ terminal) (w/o Stop and Start System) C
NG (Other terminal)



A

REPLACE COMBINATION METER ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR