A backup boost converter is built into the engine stop and start ECU. The backup boost converter helps maintain the power source voltage when the engine is restarted by stop and start control.
This prevents various functions such as the audio and visual system from malfunctioning if the power source voltage drops due to the battery voltage dropping when the engine is restarted by stop and start control.
If any DTCs are output, troubleshoot the DTCs first.
A relay function and fuse function are provided in the backup boost converter.
If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).
When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.
The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.
*: A semiconductor fuse self resets according to electric signal.
Tire pressure warning system
Toyota multi operation touch system
Headup display system
Pre-Collision System
Air conditioning system
Parking support brake system
Lane tracing assist system
Vehicle stability control system
Meter / gauge System
Navigation system
Lighting system
Refer to DTC P323A19.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>P323A19
Before replacing the engine stop and start ECU, read the number of starter operations, total number of engine starts and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Determine the trouble area by referring to the table below.
| Effect on Vehicle | Trouble Area/Cause | Fail-safe | DTC Output | Stop and start cancel indicator | Symptom | Proceed to |
|---|---|---|---|---|---|---|
| When the engine is restarted by stop and start control: The following symptoms may occur
·
Audio and visual system is reset
·
The combination meter assembly fades out |
Backup boost converter internal malfunction
·
Internal power source malfunction
·
Internal power source overvoltage
·
Duty error
·
Communication cycle error |
Stop and start control prohibited | P323A00 P323AA2 P323B29 P323B38 |
Blinks | Converter output voltage cannot be boosted when the engine is restarted | A |
| Battery voltage drop | ||||||
| Systems on the converter output side do not operate B41 terminal: Both of the following will not operate
·
Tire pressure warning system
·
Vehicle stability control system B42 terminal: The navigation system will not operate B43 terminal: Both of the following will not operate
·
Navigation system
·
Headup display system
·
Air conditioning system
·
Toyota multi operation touch system
·
Lighting system IG41 terminal: All of the following will not operate
·
Tire pressure warning system
·
Toyota multi operation touch system
·
Headup display system
·
Air conditioning system
·
Parking support brake system
·
Pre-Collision System |
Overcurrent applied to an output terminal (output terminal relay circuit is shutoff) | Stop and start control is prohibited (Connected ECUs or sensors may detect power source malfunction DTCs) |
P323A19 | Blinks | Systems do not operate as power supply from the converter is cut off | A |
| Systems do not operate (Due to converter input side malfunction) IGP terminal: All of the following will not operate
·
Tire pressure warning system
·
Toyota multi operation touch system
·
Headup display system
·
Air conditioning system
·
Parking support brake system
·
Lane tracing assist system
·
Vehicle stability control system
·
Meter / gauge system
·
Pre-Collision System IGR terminal: - ACC terminal: All of the following will not operate
·
Navigation system
·
Toyota multi operation touch system
·
Air conditioning system |
Converter input circuit malfunction
·
Open or short to GND in IGR circuit
·
Open or short to GND in IGP circuit
·
Open or short to GND in ACC circuit |
Stop and start control prohibited | - | Does not blink (Blinks when communication error DTCs are stored) | Systems do not operate as power supply from the converter is cut off | B |
| Systems on the converter output side do not operate (varies depending on the malfunctioning relay circuit the converter detected) AC42 terminal: All of the following will not operate
·
Navigation system
·
Toyota multi operation touch system
·
Air conditioning system IG12 terminal: The meter / gauge system will not operate IG31 terminal: All of the following will not operate
·
Lane tracing assist system
·
Vehicle stability control system IG41 terminal: All of the following will not operate
·
Tire pressure warning system
·
Toyota multi operation touch system
·
Headup display system
·
Air conditioning system
·
Parking support brake system
·
Pre-Collision System B41 terminal: Both of the following will not operate
·
Tire pressure warning system
·
Vehicle stability control system B42 terminal: The navigation system will not operate B43 terminal: Both of the following will not operate
·
Navigation system
·
Headup display system
·
Air conditioning system
·
Toyota multi operation touch system
·
Lighting system |
Malfunction in circuits the converter supplies power to (between the converter and ECUs or sensors) |
Related systems do not operate as the relay circuit in the converter is turned off | - | Does not blink (Blinks when communication error DTCs are stored) | Systems do not operate as power supply from the converter is cut off | B |
| All of the following systems do not operate
·
Tire Pressure Warning System
·
Toyota Multi Operation Touch System
·
Headup Display System
·
Air Conditioning System
·
Parking Support Brake System
·
Lane tracing assist system
·
Vehicle Stability Control System
·
Meter / Gauge System
·
Navigation System
·
Lighting System
·
Pre-Collision System |
·
Open in BBC fuse circuit
·
Short in converter circuit
·
Backup boost converter malfunction |
Stop and start control prohibited | P061519 | Does not blink (Due to disabled meter / gauge system) | All systems that the converter supplies power to do not operate (see circuit diagram) | A |
| P30DF62 P30EF4B P323A00 P323A16 P323AA2 P323B29 P323B38 |
||||||
| The audio does not operate (until the ignition switch is turned off) | Excessive audio volume Data List item "State of BBC" displays "BBC Overcurrent" while the circuit is protected | The relay circuit in the converter is turned off to cut off power supply to the audio and visual system (navigation system) (Returns to normal when the ignition switch is turned off) | - | Does not blink | If overcurrent is detected in the audio and visual system (navigation system), system operation is disabled while the ignition switch is ON (Returns to normal when the ignition switch is turned off) | C |
| The external backup boost converter (eco run vehicle converter assembly) output side system does not operate
·
Navigation system
·
Audio and visual system
·
Active noise control system |
·
Open in PA-BBC fuse circuit
·
Malfunction in circuits the converter supplies power to
·
External backup boost converter (eco run vehicle converter assembly) malfunction |
- | - | Does not blink | All systems that the converter supplies power to do not operate (see circuit diagram) | D |
|
·
The combination meter assembly cannot be turned off (short between IG12 and +B)
·
Communication error DTCs may be stored due to short between AC42 and +B
|
Converter circuit malfunction
·
Short between IG12 and +B
·
Short between AC42 and +B |
- | - | Does not blink | The converter cannot shut off the power source when the ignition switch is turned off | B |
|
·
Ignition switch cannot be turned off from ACC (short between ACC and +B)
·
Ignition switch cannot be turned off from ON (short between IG1 or IG2 and +B) |
Engine stop and start ECU power source circuit malfunction
·
Short between ACC and +B
·
Short between IG1 and +B
·
Short between IG2 and +B |
- | - | Does not blink |
·
Ignition switch does not turn ACC
·
Ignition switch cannot be turned off |
B |
| Proceed to |
|---|
| A |
| B |
| C |
| D |
A
B
C
D
Disconnect the engine stop and start ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B37)Location & Routingewd_type=routing;type=c;code=B37 Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B37;pinno=1,3 |
||
| B37-1 (BIN2) - Body ground | Always | 9.5 to 14 V |
| B37-3 (BIN1) - Body ground | Always | 9.5 to 14 V |
Turn the ignition switch to ACC.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57)Location & Routingewd_type=routing;type=c;code=I57 |
||
| I57-19 (ACC) - Body ground | Ignition switch ACC | 9.5 to 14 V |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57)Location & Routingewd_type=routing;type=c;code=I57 |
||
| I57-21 (IGR) - Body ground | Ignition switch ON | 9.5 to 14 V |
| I57-18 (IGP) - Body ground | Ignition switch ON | 9.5 to 14 V |
Turn the ignition switch off.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57)Location & Routingewd_type=routing;type=c;code=I57 |
||
| I57-21 (IGR) - Body ground | Ignition switch off | 0 to 1 V |
| I57-19 (ACC) - Body ground | Ignition switch off | 0 to 1 V |
| I57-18 (IGP) - Body ground | Ignition switch off | 0 to 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connector from the corresponding system ECU/sensor.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,T11)Location & Routingewd_type=routing;type=c,c;code=I57,T11 Click Connector(T11)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assemblyewd_type=component;type=c;code=T11;pinno=1,7 |
||
| I57-3 (IG41) - T11-1 (IG) | Always | Below 1 Ω |
| I57-2 (B41) - T11-7 (+B) | Always | Below 1 Ω |
| I57-3 (IG41) - Body ground | Always | 10 kΩ or higher |
| T11-1 (IG) - Body ground | Always | 10 kΩ or higher |
| I57-2 (B41) - Body ground | Always | 10 kΩ or higher |
| T11-7 (+B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I22)Location & Routingewd_type=routing;type=c,c;code=I57,I22 |
||
| I57-3 (IG41) - I22-4 (IG+) | Always | Below 1 Ω |
| I57-26 (AC42) - I22-3 (ACC) | Always | Below 1 Ω |
| I57-11 (B43) - I22-1 (B) | Always | Below 1 Ω |
| I57-3 (IG41) - Body ground | Always | 10 kΩ or higher |
| I22-4 (IG+) - Body ground | Always | 10 kΩ or higher |
| I57-26 (AC42) - Body ground | Always | 10 kΩ or higher |
| I22-3 (ACC) - Body ground | Always | 10 kΩ or higher |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| I22-1 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I17)Location & Routingewd_type=routing;type=c,c;code=I57,I17 |
||
| I57-3 (IG41) - I17-1 (IG) | Always | Below 1 Ω |
| I57-11 (B43) - I17-2 (B) | Always | Below 1 Ω |
| I57-3 (IG41) - Body ground | Always | 10 kΩ or higher |
| I17-1 (IG) - Body ground | Always | 10 kΩ or higher |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| I17-2 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,Q52)Location & Routingewd_type=routing;type=c,c;code=I57,Q52 Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assemblyewd_type=component;type=c;code=Q52;pinno=10 |
||
| I57-3 (IG41) - Q52-10 (IG) | Always | Below 1 Ω |
| I57-3 (IG41) - Body ground | Always | 10 kΩ or higher |
| Q52-10 (IG) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I58)Location & Routingewd_type=routing;type=c,c;code=I57,I58 |
||
| I57-3 (IG41) - I58-1 (IG) | Always | Below 1 Ω |
| I57-3 (IG41) - Body ground | Always | 10 kΩ or higher |
| I58-1 (IG) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I78)Location & Routingewd_type=routing;type=c,c;code=I57,I78 |
||
| I57-3 (IG41) - I78-8 (IG+) | Always | Below 1 Ω |
| I57-26 (AC42) - I78-7 (ACC) | Always | Below 1 Ω |
| I57-11 (B43) - I78-16 (+B) | Always | Below 1 Ω |
| I57-3 (IG41) - Body ground | Always | 10 kΩ or higher |
| I78-8 (IG+) - Body ground | Always | 10 kΩ or higher |
| I57-26 (AC42) - Body ground | Always | 10 kΩ or higher |
| I78-7 (ACC) - Body ground | Always | 10 kΩ or higher |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| I78-16 (+B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,A10)Location & Routingewd_type=routing;type=c,c;code=I57,A10 Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assemblyewd_type=component;type=c;code=A10;pinno=8 |
||
| I57-3 (IG41) - A10-8 (IGB) | Always | Below 1 Ω |
| I57-3 (IG41) - Body ground | Always | 10 kΩ or higher |
| A10-8 (IGB) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I71)Location & Routingewd_type=routing;type=c,c;code=I57,I71 |
||
| I57-23 (IG31) - I71-1 (IG) | Always | Below 1 Ω |
| I57-23 (IG31) - Body ground | Always | 10 kΩ or higher |
| I71-1 (IG) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,B19)Location & Routingewd_type=routing;type=c,c;code=I57,B19 |
||
| I57-23 (IG31) - B19-31 (IG1) | Always | Below 1 Ω |
| I57-2 (B41) - B19-14 (+BI1) | Always | Below 1 Ω |
| I57-23 (IG31) - Body ground | Always | 10 kΩ or higher |
| B19-31 (IG+) - Body ground | Always | 10 kΩ or higher |
| I57-2 (B41) - Body ground | Always | 10 kΩ or higher |
| B19-14 (+BI1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,B20)Location & Routingewd_type=routing;type=c,c;code=I57,B20 |
||
| I57-23 (IG31) - B20-45 (IG1) | Always | Below 1 Ω |
| I57-23 (IG31) - Body ground | Always | 10 kΩ or higher |
| B20-45 (IG1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I5)Location & Routingewd_type=routing;type=c,c;code=I57,I5 |
||
| I57-10 (IG12) - I5-6 (IG+) | Always | Below 1 Ω |
| I57-10 (IG12) - Body ground | Always | 10 kΩ or higher |
| I5-6 (IG+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I8)Location & Routingewd_type=routing;type=c,c;code=I57,I8 |
||
| I57-26 (AC42) - I8-3 (ACC1) | Always | Below 1 Ω |
| I57-12 (B42) - I8-4 (+B1) | Always | Below 1 Ω |
| I57-26 (AC42) - Body ground | Always | 10 kΩ or higher |
| I8-3 (ACC1) - Body ground | Always | 10 kΩ or higher |
| I57-12 (B42) - Body ground | Always | 10 kΩ or higher |
| I8-4 (+B1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I10)Location & Routingewd_type=routing;type=c,c;code=I57,I10 |
||
| I57-26 (AC42) - I10-15 (ACC1) | Always | Below 1 Ω |
| I57-12 (B42) - I10-4 (+B1) | Always | Below 1 Ω |
| I57-26 (AC42) - Body ground | Always | 10 kΩ or higher |
| I10-15 (ACC1) - Body ground | Always | 10 kΩ or higher |
| I57-12 (B42) - Body ground | Always | 10 kΩ or higher |
| I10-4 (+B1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I18)Location & Routingewd_type=routing;type=c,c;code=I57,I18 |
||
| I57-26 (AC42) - I18-24 (ACC) | Always | Below 1 Ω |
| I57-11 (B43) - I18-12 (B) | Always | Below 1 Ω |
| I57-26 (AC42) - Body ground | Always | 10 kΩ or higher |
| I18-24 (ACC) - Body ground | Always | 10 kΩ or higher |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| I18-12 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I21)Location & Routingewd_type=routing;type=c,c;code=I57,I21 |
||
| I57-11 (B43) - I21-10 (+B) | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| I21-10 (+B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I61)Location & Routingewd_type=routing;type=c,c;code=I57,I61 |
||
| I57-11 (B43) - I61-2 (B) | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| I61-2 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,I62)Location & Routingewd_type=routing;type=c,c;code=I57,I62 |
||
| I57-11 (B43) - I62-2 (B) | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| I62-2 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,i6)Location & Routingewd_type=routing;type=c,c;code=I57,i6 Click Connector(i6)Seat>Front Seat Wire LH>Foot Light LH (No. 1 Interior Illumination Light Assembly LH)ewd_type=component;type=c;code=i6;pinno=2 |
||
| I57-11 (B43) - i6-2 | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| i6-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,h11)Location & Routingewd_type=routing;type=c,c;code=I57,h11 Click Connector(h11)Seat>Front Seat Wire RH>Foot Light RH (No. 1 Interior Illumination Light Assembly RH)ewd_type=component;type=c;code=h11;pinno=2 |
||
| I57-11 (B43) - h11-2 | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| h11-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,P5)Location & Routingewd_type=routing;type=c,c;code=I57,P5 Click Connector(P5)Body>No. 2 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly LHewd_type=component;type=c;code=P5;pinno=1 |
||
| I57-11 (B43) - P5-1 (+) | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| P5-1 (+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,O5)Location & Routingewd_type=routing;type=c,c;code=I57,O5 Click Connector(O5)Body>No. 1 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly RHewd_type=component;type=c;code=O5;pinno=1 |
||
| I57-11 (B43) - O5-1 (+) | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| O5-1 (+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,N8)Location & Routingewd_type=routing;type=c,c;code=I57,N8 Click Connector(N8)Body>Front Door Wire LH>Front Door Inside Handle Illumination Light Assembly LHewd_type=component;type=c;code=N8;pinno=1 |
||
| I57-11 (B43) - N8-1 (+) | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| N8-1 (+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,M10)Location & Routingewd_type=routing;type=c,c;code=I57,M10 Click Connector(M10)Body>Front Door Wire RH>Front Door Inside Handle Illumination Light Assembly RHewd_type=component;type=c;code=M10;pinno=1 |
||
| I57-11 (B43) - M10-1 (+) | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| M10-1 (+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,d5,d9)Location & Routingewd_type=routing;type=c,c,c;code=I57,d5,d9 Click Connector(d5)Body>No. 1 Roof Wire>Vanity Light Assembly LHewd_type=component;type=c;code=d5;pinno=1 Click Connector(d9)Body>No. 1 Roof Wire>Vanity Light Assembly LHewd_type=component;type=c;code=d9;pinno=2 |
||
| I57-11 (B43) - d5-1 (B)*8 | Always | Below 1 Ω |
| I57-11 (B43) - d9-2 (B)*9 | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| d5-1 (B)*8 - Body ground | Always | 10 kΩ or higher |
| d9-2 (B)*9 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57,d4,d8)Location & Routingewd_type=routing;type=c,c,c;code=I57,d4,d8 Click Connector(d4)Body>No. 1 Roof Wire>Vanity Light Assembly RHewd_type=component;type=c;code=d4;pinno=1 Click Connector(d8)Body>No. 1 Roof Wire>Vanity Light Assembly RHewd_type=component;type=c;code=d8;pinno=2 |
||
| I57-11 (B43) - d4-1 (B)*8 | Always | Below 1 Ω |
| I57-11 (B43) - d8-2 (B)*9 | Always | Below 1 Ω |
| I57-11 (B43) - Body ground | Always | 10 kΩ or higher |
| d4-1 (B)*8 - Body ground | Always | 10 kΩ or higher |
| d8-2 (B)*9 - Body ground | Always | 10 kΩ or higher |
*1: for 12.3 Inch Display
*2: w/ Headup Display System
*3: w/ Rear Heater
*4: w/ Pre-collision System
*5: w/ Lane Tracing Assist System
*6: Except 14 Speaker
*7: for 14 Speaker
*8: for Bulb Type
*9: for LED Type
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connector from the corresponding system ECU/sensor.
Measure the voltage according to the value(s) in the table below.
Measure the voltage at the corresponding terminals.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: except 14 speaker *2: for 14 speaker *3: for 12.3 Inch Display *4: w/ Headup Display System *5: for bulb type *6: for LED type |
||
Click Location & Routing(T11,B19,I8,I10,I18,I22,I21,I17,I78,I61,I62,i6,h11,P5,O5,N8,M10,d5,d9,d4,d8)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c,c;code=T11,B19,I8,I10,I18,I22,I21,I17,I78,I61,I62,i6,h11,P5,O5,N8,M10,d5,d9,d4,d8 Click Connector(T11)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assemblyewd_type=component;type=c;code=T11;pinno=7 Click Connector(i6)Seat>Front Seat Wire LH>Foot Light LH (No. 1 Interior Illumination Light Assembly LH)ewd_type=component;type=c;code=i6;pinno=2 Click Connector(h11)Seat>Front Seat Wire RH>Foot Light RH (No. 1 Interior Illumination Light Assembly RH)ewd_type=component;type=c;code=h11;pinno=2 Click Connector(P5)Body>No. 2 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly LHewd_type=component;type=c;code=P5;pinno=1 Click Connector(O5)Body>No. 1 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly RHewd_type=component;type=c;code=O5;pinno=1 Click Connector(N8)Body>Front Door Wire LH>Front Door Inside Handle Illumination Light Assembly LHewd_type=component;type=c;code=N8;pinno=1 Click Connector(M10)Body>Front Door Wire RH>Front Door Inside Handle Illumination Light Assembly RHewd_type=component;type=c;code=M10;pinno=1 Click Connector(d5)Body>No. 1 Roof Wire>Vanity Light Assembly LHewd_type=component;type=c;code=d5;pinno=1 Click Connector(d9)Body>No. 1 Roof Wire>Vanity Light Assembly LHewd_type=component;type=c;code=d9;pinno=2 Click Connector(d4)Body>No. 1 Roof Wire>Vanity Light Assembly RHewd_type=component;type=c;code=d4;pinno=1 Click Connector(d8)Body>No. 1 Roof Wire>Vanity Light Assembly RHewd_type=component;type=c;code=d8;pinno=2 |
||
| T11-7 (+B) - Body ground | Always | 10.5 to 16 V |
| B19-14 (+BI1) - Body ground | Always | 10.5 to 16 V |
| I8-4 (+B1)*1 - Body ground | Always | 10.5 to 16 V |
| I10-4 (+B1)*2 - Body ground | Always | 10.5 to 16 V |
| I18-12 (B)*3 - Body ground | Always | 10.5 to 16 V |
| I22-1 (B)*3 - Body ground | Always | 10.5 to 16 V |
| I21-10 (+B) - Body ground | Always | 10.5 to 16 V |
| I17-2 (B)*4 - Body ground | Always | 10.5 to 16 V |
| I78-16 (+B) - Body ground | Always | 10.5 to 16 V |
| I61-2 (B) - Body ground | Always | 10.5 to 16 V |
| I62-2 (B) - Body ground | Always | 10.5 to 16 V |
| i6-2 - Body ground | Always | 10.5 to 16 V |
| h11-2 - Body ground | Always | 10.5 to 16 V |
| P5-1 (+) - Body ground | Always | 10.5 to 16 V |
| O5-1 (+) - Body ground | Always | 10.5 to 16 V |
| N8-1 (+) - Body ground | Always | 10.5 to 16 V |
| M10-1 (+) - Body ground | Always | 10.5 to 16 V |
| d5-1 (B)*5 - Body ground | Always | 10.5 to 16 V |
| d9-2 (B)*6 - Body ground | Always | 10.5 to 16 V |
| d4-1 (B)*5 - Body ground | Always | 10.5 to 16 V |
| d8-2 (B)*6 - Body ground | Always | 10.5 to 16 V |
Turn the ignition switch to ACC.
Measure the voltage according to the value(s) in the table below.
Measure the voltage at the corresponding terminals.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
*1: except 14 speaker *2: for 14 speaker *3: w/ Headup Display System |
||
Click Location & Routing(I8,I10,I18,I22,I78)Location & Routingewd_type=routing;type=c,c,c,c,c;code=I8,I10,I18,I22,I78 |
||
| I8-3 (ACC1)*1 - Body ground | Ignition switch ACC | 10.5 to 16 V |
| I10-15 (ACC1)*2 - Body ground | Ignition switch ACC | 10.5 to 16 V |
| I18-24 (ACC)*3 - Body ground | Ignition switch ACC | 10.5 to 16 V |
| I22-3 (ACC) - Body ground | Ignition switch ACC | 10.5 to 16 V |
| I78-7 (ACC) - Body ground | Ignition switch ACC | 10.5 to 16 V |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
Measure the voltage at the corresponding terminals.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
*1: for 12.3 Inch Display *2: w/ Headup Display System *3: w/ Pre-collision System *4: w/ Rear Heater *5: w/ Lane Tracing Assist System |
||
Click Location & Routing(T11,I22,I17,A10,Q52,I58,I78,I71,B19,B20,I5)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c,c,c,c,c;code=T11,I22,I17,A10,Q52,I58,I78,I71,B19,B20,I5 Click Connector(T11)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assemblyewd_type=component;type=c;code=T11;pinno=1 Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assemblyewd_type=component;type=c;code=A10;pinno=8 Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assemblyewd_type=component;type=c;code=Q52;pinno=10 |
||
| T11-1 (IG) - Body ground | Ignition switch ON | 10.5 to 16 V |
| I22-4 (IG+)*1 - Body ground | Ignition switch ON | 10.5 to 16 V |
| I17-1 (IG)*2 - Body ground | Ignition switch ON | 10.5 to 16 V |
| A10-8 (IGB)*3 - Body ground | Ignition switch ON | 10.5 to 16 V |
| Q52-10 (IG)*4 - Body ground | Ignition switch ON | 10.5 to 16 V |
| I58-1 (IG) - Body ground | Ignition switch ON | 10.5 to 16 V |
| I78-8 (IG+) - Body ground | Ignition switch ON | 10.5 to 16 V |
| I71-1 (IG)*5 - Body ground | Ignition switch ON | 10.5 to 16 V |
| B19-31 (IG1) - Body ground | Ignition switch ON | 10.5 to 16 V |
| B20-45 (IG1) - Body ground | Ignition switch ON | 10.5 to 16 V |
| I5-6 (IG+) - Body ground | Ignition switch ON | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off and wait for 1 minute.
Turn the ignition switch to ON.
Lower the audio volume.
Check if the audio and visual system operates normally.
Audio and visual system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Disconnect the radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I57)Location & Routingewd_type=routing;type=c;code=I57 |
||
| I57-12 (B42) - Body ground | Always | 10 kΩ or higher |
| I57-26 (AC42) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for Radio Receiver Type:
for Radio and Display Type, for 12.3 Inch Display:
for Radio and Display Type, except 12.3 Inch Display:
NG
Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B42)Location & Routingewd_type=routing;type=c;code=B42 |
||
| B42-11 (BIN) - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.
Turn the ignition switch to ACC.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B42)Location & Routingewd_type=routing;type=c;code=B42 |
||
| B42-3 (ACC) - Body ground | Ignition switch ACC | 9.5 to 14 V |
Turn the ignition switch off.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B42)Location & Routingewd_type=routing;type=c;code=B42 |
||
| B42-3 (ACC) - Body ground | Ignition switch off | 0 to 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B42)Location & Routingewd_type=routing;type=c;code=B42 |
||
| B42-6 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.
Disconnect the connector from the corresponding system ECU/sensor.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B42,S25)Location & Routingewd_type=routing;type=c,c;code=B42,S25 Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assemblyewd_type=component;type=c;code=S25;pinno=15 |
||
| B42-5 (BO1) - S25-15 (+B) | Always | Below 1 Ω |
| B42-5 (BO1)or S25-15 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for 14 Speaker *2: Except 14 Speaker |
||
Click Location & Routing(B42,S22)Location & Routingewd_type=routing;type=c,c;code=B42,S22 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=1,16 |
||
| B42-5 (BO1) - S22-1 (+B)*1 | Always | Below 1 Ω |
| B42-5 (BO1) - S22-16 (+B2)*2 | Always | Below 1 Ω |
| B42-5 (BO1)or S22-1 (+B)*1or S22-16 (+B2)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connector from the corresponding system ECU/sensor.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for 14 Speaker *2: Except 14 Speaker |
||
Click Location & Routing(S25,S22)Location & Routingewd_type=routing;type=c,c;code=S25,S22 Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assemblyewd_type=component;type=c;code=S25;pinno=15 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=1,16 |
||
| S25-15 (+B) - Body ground | Ignition switch ACC | 10.5 to 16 V |
| S22-1 (+B)*1 - Body ground | Ignition switch ACC | 10.5 to 16 V |
| S22-16 (+B2)*2 - Body ground | Ignition switch ACC | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.
Disconnect the power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B42)Location & Routingewd_type=routing;type=c;code=B42 |
||
| B42-3 (ACC) - 5C-12 | Always | Below 1 Ω |
| B42-3 (ACC) or 5C-12 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG