PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE (-) BATTERY TERMINAL
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
CAUTION REGARDING INTERFERENCE WITH ELECTRONIC DEVICES
As weak radio waves are emitted from the electrical key transmitter sub-assembly, if a pacemaker is being used, be sure to read the pacemaker instruction manual and the following.
People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should keep away from the entry and start system antennas. The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your dealer for details, such as the frequency of radio waves and timing of the emitted radio waves. Then, consult your doctor to see if you should disable the entry function.
User of any electrical medical device other than implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.
Ask your dealer for details for disabling the entry and start system.
|
*: w/ Rear Door Entry Function |
|
| Exterior antenna |
·
Front door outside handle assembly (for Driver Door)
·
Front door outside handle assembly (for Front Passenger Door)
·
Rear door outside handle assembly LH*
·
Rear door outside handle assembly RH*
·
Electrical key antenna (outside luggage compartment) |
| Interior antenna |
·
No. 1 indoor electrical key antenna assembly (front floor)
·
No. 3 indoor electrical key antenna assembly (rear floor)
·
No. 3 indoor electrical key antenna assembly (inside luggage compartment) |
The entry and start system can be disabled by a customize setting.
PRECAUTION WHEN USING GTS
When the ignition switch is turned off, the DTCs stored in the steering lock ECU (steering lock actuator with ECU assembly) will be cleared. Be sure to record any output DTCs immediately.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
PRECAUTIONS FOR BATTERY
If the battery became discharged and then was charged or the cable was disconnected and reconnected to the (-) battery terminal, the steering lock may not be released and the engine may not be able to be started unless the driver door is opened and closed with the ignition switch off.
After the battery is removed and reinstalled, be sure to wait at least 10 seconds before the next engine start. The engine may not start immediately after the battery is reinstalled.
After disconnecting and reconnecting a cable to the battery, the engine may not start on the first attempt. If this occurs, turn the ignition switch off. The engine will start normally from the second time onward.
When a cable to the is disconnected and reconnected, the power source mode returns to the mode it was in before the cable was disconnected.
PRECAUTION FOR REGISTRATION
If replacing any of the following parts, refer to Service Bulletin.
*: w/ Fingerprint Authentication
Certification ECU (smart key ECU assembly)
Steering lock ECU (steering lock actuator with ECU assembly)
ECM
Electrical key transmitter sub-assembly
ID code box (immobiliser code ECU)
Main body ECU (multiplex network body ECU)
Engine switch*
PRECAUTIONS FOR STEERING LOCK/UNLOCK FUNCTION
After turning the ignition switch off and opening and closing any of the doors, the steering wheel will be locked due to the steering lock function. Operating the engine switch again automatically cancels the steering lock function.
To prevent the steering lock motor from overheating, the motor operation may be suspended if the steering is locked and unlocked repeatedly in a short period of time. In this case, refrain from operating the engine switch. After about 10 seconds, the steering lock motor will resume functioning.
PRECAUTION WHEN HANDLING ENGINE SWITCH WITH FINGERPRINT AUTHENTICATION FUNCTION
When cleaning the surface of the sensor, use a soft, dry cloth without any fibers sticking out.
Any moisture or dirt on the surface of the fingerprint sensor or on the finger operating the sensor could cause a malfunction.
Clean the fingerprint sensor immediately if there is any substance (dust, sand, paint, ink, soap, detergent, acid or acidic food, oil, lotion, etc.) that could cause a malfunction on it.
Avoid using detergents (such as glass cleaner, spray-type liquid cleaner, solvents, or ammonia) and abrasives (such as wax or sandpaper), as using these could cause a malfunction.