Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B227411  ACC Circuit Short to Ground  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit between terminal ACCD of the certification ECU (smart key ECU assembly) and the ACC relay.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B227411 ACC Circuit Short to Ground The ACC relay circuit of the certification ECU (smart key ECU assembly) is malfunctioning. (1-trip detection logic*)
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

Power distribution box assembly

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Wait 10 seconds after turning the ignition switch to ACC or ON, and then wait another 10 seconds after turning the ignition switch off.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the ACC relay being stuck on, the ACC relay does not turn off even though the ignition switch is off.

·

If there is a malfunction due to the ACC relay being stuck off, the ACC relay does not turn on even though the ignition switch is ACC.


HINT:

The ignition switch can be turned to ON and the engine can be started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B227411
Power Source Control
·

ACC Relay Monitor



WIRING DIAGRAM

B586656E24
2.375,0.75 4.073,1.073 1.698,0.323 10 false from Battery 2.521,2.677 3.073,2.906 0.552,0.229 10 false ACC 1.5,2.031 2.313,2.26 0.813,0.229 10 false ECU-ACC 0.958,1.646 1.302,1.885 0.344,0.24 10 false 12 0.958,2.177 1.302,2.417 0.344,0.24 10 false 36 3.99,1.635 4.333,1.875 0.344,0.24 10 false 1 3.958,2.156 4.302,2.396 0.344,0.24 10 false 39 0.948,1.875 1.292,2.115 0.344,0.24 10 false 5B 3.969,1.875 4.313,2.115 0.344,0.24 10 false 5H 5.135,3.583 5.479,3.823 0.344,0.24 10 false I39 5.125,3.75 6.656,4.448 1.531,0.698 10 false Certification ECU (Smart Key ECU Assembly) 4.99,2.292 5.333,2.531 0.344,0.24 10 false 21 5.26,2.281 5.813,2.51 0.552,0.229 10 false ACCD 5.76,1.875 6.104,2.115 0.344,0.24 10 false +B 6.229,2.271 6.573,2.51 0.344,0.24 10 false IC 1.542,3.396 4.771,3.917 3.229,0.521 10 false Power Distribution Box Assembly 0.948,2.406 1.292,2.646 0.344,0.24 10 false 5B 3.927,2.385 4.271,2.625 0.344,0.24 10 false 5B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER DISTRIBUTION BOX ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 5B power distribution box assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I39)Location & Routing

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I39-21 (ACCD) - 5B-39 Always Below 1 Ω
5B-36 - Body ground Always Below 1 Ω
I39-21 (ACCD) or 5B-39 - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B574624C61
1.625,0.052 1.979,0.24 0.354,0.188 2.667,1.917 2.479,1.917 2.479,1.917 2.396,0.938 true 0.177,0.073 0.49,0.271 0.313,0.198 10 false *a 1.708,0.073 2.021,0.271 0.313,0.198 10 false I39 2.719,1.854 3.333,2.052 0.615,0.198 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I39)Location & Routing

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I39-21 (ACCD) - Body ground Ignition switch off 1 V or less
I39-21 (ACCD) - Body ground Ignition switch ACC 8.5 V or higher


Result:
Proceed to
OK
NG




OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)