Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467512 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B276C88  Alarm / Wiper LIN Bus off  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B276C88 Alarm / Wiper LIN Bus off No communication between main body ECU (multiplex network body ECU), rain sensor and map light sub-assembly for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Map light assembly

·

Rain sensor

·

Harness or connector


Main Body A

WIRING DIAGRAM

B486902E43
0.354,1.656 2.083,2.115 1.729,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 5.094,3.51 7.052,3.979 1.958,0.469 10 false Rain Sensor 5.146,1.677 6.896,2.021 1.75,0.344 10 false Map Light Assembly 0.354,1.5 0.813,1.698 0.458,0.198 10 false I2 1.625,0.979 2,1.146 0.375,0.167 10 false LIN4 2,0.823 2.24,1.063 0.24,0.24 10 false 11 5.104,3.344 6.177,3.563 1.073,0.219 10 false d23 0.74,4.365 2.76,4.625 2.021,0.26 10 false : LIN Communication Line 5.281,2.813 5.74,3.01 0.458,0.198 10 false MPX 5.083,2.656 5.24,2.854 0.156,0.198 10 false 3 5.146,1.5 5.604,1.698 0.458,0.198 10 false d2 5.281,0.969 5.74,1.167 0.458,0.198 10 false LIN1 5.031,0.802 5.344,1 0.313,0.198 10 false 13

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

b.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B276C88 is output A
DTC B276C88 is not output B



A

2.CHECK MAP LIGHT ASSEMBLY

B

2.CHECK MAP LIGHT ASSEMBLY
a.

Disconnect the d2 map light assembly connector.


b.

Check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B276C88 is output A
DTC B276F87 is output B



A

3.CHECK RAIN SENSOR

B

REPLACE MAP LIGHT ASSEMBLY

3.CHECK RAIN SENSOR
a.

Disconnect the d23 rain sensor connector.


b.

Check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B276C88 is output A
DTC B127987 is output B



A

4.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

B

4.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
a.

Reconnect the I2 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the d2 map light assembly connector.


c.

Disconnect the d23 rain sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I2)Location & Routing

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

I2-11 (LIN4) - Body ground Always 10 kΩ or higher
I2-11 (LIN4) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR