The air conditioning amplifier assembly receives ventilation volume switch signals when the ignition switch is ON, and then transmits airflow amount signals to each seat climate blower.
for LHD:
for RHD:
If the battery voltage is low, the climate control seat system may not operate. When "High Power Consumption Partial Limit on AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the battery, referring to On-vehicle Inspection for the charging system.
for 1GR-FE: Click herePower Source / Network>1GR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for V35A-FTS: Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Left Seat Blower | LH side seat blower operation | OFF/ON | - |
| Tester Display |
|---|
| Front Left Seat Blower |
| Result | Proceed to |
|---|---|
| Both seat cushion seat blower and seatback seat blower operate | A |
| Only seat cushion seat blower does not operate | B |
| Only seatback seat blower does not operate | C |
| Both seat cushion seat blower and seatback seat blower do not operate | D |
A
B
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
C
D
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Result | Proceed to |
|---|---|
| Does not operate normally with operation of either the multi-display or seat blower switch | A |
| Does not operate normally with operation of the multi-display | B |
| Does not operate normally with operation of the seat blower switch | C |
A
B
C
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL
Disconnect the p2 seatback climate control blower LH connector.
Disconnect the i7 seat cushion climate control blower assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(p2,i7)Location & Routingewd_type=routing;type=c,c;code=p2,i7 Click Connector(p2)Seat>No. 2 Front Seat Wire LH>Seat Back Climate Control Blower LH (Front Seat LH)ewd_type=component;type=c;code=p2;pinno=4,1,3 Click Connector(i7)Seat>Front Seat Wire LH>Seat Cushion Climate Control Blower Assembly LH (Front Seat LH)ewd_type=component;type=c;code=i7;pinno=4,5,6 |
||
| p2-4 (GND) - i7-4 (BFB-) | Always | Below 1 Ω |
| p2-4 (GND) or i7-4 (BFB-) - Other terminals and body ground | Always | 10 kΩ or higher |
| p2-1 (IG) - i7-5 (CTB) | Always | Below 1 Ω |
| p2-1 (IG) or i7-5 (CTB) - Other terminals and body ground | Always | 10 kΩ or higher |
| p2-3 (BFB+) - i7-6 (BBS) | Always | Below 1 Ω |
| p2-3 (BFB+) or i7-6 (BBS) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the seatback climate control blower LH with a new or known good one.
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
Disconnect the i7 seat cushion climate control blower assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i7)Location & Routingewd_type=routing;type=c;code=i7 Click Connector(i7)Seat>Front Seat Wire LH>Seat Cushion Climate Control Blower Assembly LH (Front Seat LH)ewd_type=component;type=c;code=i7;pinno=1 |
||
| i7-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| i7-1 (IG) - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i7)Location & Routingewd_type=routing;type=c;code=i7 Click Connector(i7)Seat>Front Seat Wire LH>Seat Cushion Climate Control Blower Assembly LH (Front Seat LH)ewd_type=component;type=c;code=i7;pinno=8 |
||
| i7-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the i7 seat cushion climate control blower assembly LH connector.
Disconnect the I33 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i7,I33)Location & Routingewd_type=routing;type=c,c;code=i7,I33 Click Connector(i7)Seat>Front Seat Wire LH>Seat Cushion Climate Control Blower Assembly LH (Front Seat LH)ewd_type=component;type=c;code=i7;pinno=7 |
||
| i7-7 (SIGN) - I33-14 (LOUT) | Always | Below 1 Ω |
| i7-7 (SIGN) or I33-14 (LOUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
Check for pulses according to the value(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | I33-14 (LOUT) - Body ground |
| Tool Setting | 1 V/DIV., 1 ms/DIV. |
| Vehicle Condition |
·
Ignition switch ON
·
LH side refreshing seat switch (seat blower switch) operate |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Right Seat Blower | RH side seat blower operation | OFF/ON | - |
| Tester Display |
|---|
| Front Right Seat Blower |
| Result | Proceed to |
|---|---|
| Both seat cushion seat blower and seatback seat blower operate | A |
| Only seat cushion seat blower does not operate | B |
| Only seatback seat blower does not operate | C |
| Both seat cushion seat blower and seatback seat blower do not operate | D |
A
B
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
C
D
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Result | Proceed to |
|---|---|
| Does not operate normally with operation of either the multi-display or seat blower switch | A |
| Does not operate normally with operation of the multi-display | B |
| Does not operate normally with operation of the seat blower switch | C |
A
B
C
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL
Disconnect the h12 seatback climate control blower RH connector.
Disconnect the o1 seat cushion climate control blower assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(o1,h12)Location & Routingewd_type=routing;type=c,c;code=o1,h12 Click Connector(o1)Seat>No. 2 Front Seat Wire RH>Seat Back Climate Control Blower RH (Front Seat RH)ewd_type=component;type=c;code=o1;pinno=4,1,3 Click Connector(h12)Seat>Front Seat Wire RH>Seat Cushion Climate Control Blower Assembly RH (Front Seat RH)ewd_type=component;type=c;code=h12;pinno=4,5,6 |
||
| o1-4 (GND) - h12-4 (BFB-) | Always | Below 1 Ω |
| o1-4 (GND) or h12-4 (BFB-) - Other terminals and body ground | Always | 10 kΩ or higher |
| o1-1 (IG) - h12-5 (CTB) | Always | Below 1 Ω |
| o1-1 (IG) or h12-5 (CTB) - Other terminals and body ground | Always | 10 kΩ or higher |
| o1-3 (BFB+) - h12-6 (BBS) | Always | Below 1 Ω |
| o1-3 (BFB+) or h12-6 (BBS) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the seatback climate control blower RH with a new or known good one.
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
Disconnect the h12 seat cushion climate control blower assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h12)Location & Routingewd_type=routing;type=c;code=h12 Click Connector(h12)Seat>Front Seat Wire RH>Seat Cushion Climate Control Blower Assembly RH (Front Seat RH)ewd_type=component;type=c;code=h12;pinno=1 |
||
| h12-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| h12-1 (IG) - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h12)Location & Routingewd_type=routing;type=c;code=h12 Click Connector(h12)Seat>Front Seat Wire RH>Seat Cushion Climate Control Blower Assembly RH (Front Seat RH)ewd_type=component;type=c;code=h12;pinno=8 |
||
| h12-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the h12 seat cushion climate control blower assembly RH connector.
Disconnect the I33 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(h12,I33)Location & Routingewd_type=routing;type=c,c;code=h12,I33 Click Connector(h12)Seat>Front Seat Wire RH>Seat Cushion Climate Control Blower Assembly RH (Front Seat RH)ewd_type=component;type=c;code=h12;pinno=7 |
||
| h12-7 (SIGN) - I33-13 (ROUT) | Always | Below 1 Ω |
| h12-7 (SIGN) or I33-13 (ROUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
Check for pulses according to the value(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | I33-13 (ROUT) - Body ground |
| Tool Setting | 1 V/DIV., 1 ms/DIV. |
| Vehicle Condition |
·
Ignition switch ON
·
RH side refreshing seat switch (seat blower switch) operate |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
NG