The air conditioning amplifier assembly receives ventilation volume switch signals when the ignition switch is ON, and then transmits airflow amount signals to each seat climate blower.
The climate control seat system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the climate control seat system after confirming that the communication system is functioning properly.
for 1GR-FE: Click herePower Source / Network>1GR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for V35A-FTS: Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
Inspect the fuses for circuits related to this system before performing the following procedure.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Left Seat Blower | Rear seat LH side seat blower operation | OFF/ON | - |
| Tester Display |
|---|
| Rear Left Seat Blower |
| Result | Proceed to |
|---|---|
| Both No. 1 seat cushion seat blower and No. 1 seatback seat blower operate | A |
| Only No. 1 seat cushion seat blower does not operate | B |
| Only No. 1 seatback seat blower does not operate | C |
| Both No. 1 seat cushion seat blower and No. 1 seatback seat blower do not operate | D |
A
B
C
D
Replace the cooler control switch assembly with a new or known good one.
Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH (for Rear Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Rear Side)>REMOVAL
Disconnect the k7 No. 1 seatback climate control blower assembly LH connector.
Disconnect the k4 No. 1 seat cushion climate control blower assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(k7,k4)Location & Routingewd_type=routing;type=c,c;code=k7,k4 Click Connector(k7)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Back Climate Control Blower (Rear Seat LH)ewd_type=component;type=c;code=k7;pinno=4,1,3 Click Connector(k4)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Cushion Climate Control Blower Assembly (Rear Seat LH)ewd_type=component;type=c;code=k4;pinno=4,5,6 |
||
| k7-4 (GND) - k4-4 (BFB-) | Always | Below 1 Ω |
| k7-4 (GND) or k4-4 (BFB-) - Other terminals and body ground | Always | 10 kΩ or higher |
| k7-1 (IG) - k4-5 (CTB) | Always | Below 1 Ω |
| k7-1 (IG) or k4-5 (CTB) - Other terminals and body ground | Always | 10 kΩ or higher |
| k7-3 (BFB+) - k4-6 (BBS) | Always | Below 1 Ω |
| k7-3 (BFB+) or k4-6 (BBS) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 seatback climate control blower assembly LH with a new or known good one.
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for LH Side)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the k4 No. 1 seat cushion climate control blower assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(k4)Location & Routingewd_type=routing;type=c;code=k4 Click Connector(k4)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Cushion Climate Control Blower Assembly (Rear Seat LH)ewd_type=component;type=c;code=k4;pinno=1 |
||
| k4-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| k4-1 (IG) - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(k4)Location & Routingewd_type=routing;type=c;code=k4 Click Connector(k4)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Cushion Climate Control Blower Assembly (Rear Seat LH)ewd_type=component;type=c;code=k4;pinno=8 |
||
| k4-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the k4 No. 1 seat cushion climate control blower assembly LH connector.
Disconnect the I31 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(k4,I31)Location & Routingewd_type=routing;type=c,c;code=k4,I31 Click Connector(k4)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Cushion Climate Control Blower Assembly (Rear Seat LH)ewd_type=component;type=c;code=k4;pinno=7 |
||
| k4-7 (SIGN) - I31-22 (SV2L) | Always | Below 1 Ω |
| k4-7 (SIGN) or I31-22 (SV2L) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
Check for pulses according to the value(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | I31-22 (SV2L) - Body ground |
| Tool Setting | 1 V/DIV., 1 ms/DIV. |
| Vehicle Condition |
·
Ignition switch ON
·
Rear left side refreshing seat switch (seat blower switch) on |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG