Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM38G0E _58 Vehicle Interior _100628 SEAT _0467518 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Folding Motor Circuit  


DESCRIPTION

The fold seat control ECU receives switch operation signals from the No. 1 and No. 2 fold seat switches and activates the power seat motors. At this time, the Hall IC detects the actuation of the seat cushion and sends a seat cushion actuation signal to the fold seat control ECU. The fold seat control ECU uses signals from the Hall IC to detect if an object is caught or if any other abnormal condition has occurred.

WIRING DIAGRAM

for LH Side


C458746E01
1.844,0.906 2.219,1.063 0.375,0.156 10 false FLD+ 1.885,1.625 2.229,1.781 0.344,0.156 10 false FLD- 1.854,2.219 2.229,2.375 0.375,0.156 10 false SFLD 2.354,0.917 2.583,1.125 0.229,0.208 10 false T8 2.344,1.594 2.688,1.823 0.344,0.229 10 false T8 2.354,2.219 2.531,2.375 0.177,0.156 10 false T6 2.406,0.74 2.5,0.896 0.094,0.156 10 false 6 2.365,1.417 2.542,1.573 0.177,0.156 10 false 7 2.365,2.042 2.542,2.198 0.177,0.156 10 false 10 1,3.552 2.75,4.042 1.75,0.49 10 false Fold Seat Control ECU 4.521,0.813 4.615,0.969 0.094,0.156 10 false 4 4.521,1.479 4.615,1.635 0.094,0.156 10 false 1 4.521,2.104 4.615,2.26 0.094,0.156 10 false 2 4.51,2.833 4.719,3.094 0.208,0.26 10 false 3 4.531,3.542 4.802,3.698 0.271,0.156 10 false m2 4.531,3.75 6.729,4.188 2.198,0.438 10 false No. 2 Rear Seat Leg Assembly LH 2.344,2.948 2.594,3.198 0.25,0.25 10 false T6 2.333,2.74 2.573,2.958 0.24,0.219 10 false 12 1.927,2.969 2.302,3.125 0.375,0.156 10 false SG1


for RH Side


C458746E02
1.844,0.906 2.219,1.063 0.375,0.156 10 false FLD+ 1.885,1.625 2.229,1.781 0.344,0.156 10 false FLD- 1.854,2.219 2.229,2.375 0.375,0.156 10 false SFLD 2.354,0.917 2.583,1.125 0.229,0.208 10 false T7 2.344,1.594 2.688,1.823 0.344,0.229 10 false T7 2.354,2.219 2.531,2.375 0.177,0.156 10 false T6 2.406,0.74 2.5,0.896 0.094,0.156 10 false 3 2.385,1.417 2.563,1.573 0.177,0.156 10 false 6 2.365,2.042 2.542,2.198 0.177,0.156 10 false 11 1,3.552 2.75,4.042 1.75,0.49 10 false Fold Seat Control ECU 4.521,0.813 4.615,0.969 0.094,0.156 10 false 4 4.521,1.479 4.615,1.635 0.094,0.156 10 false 1 4.521,2.104 4.615,2.26 0.094,0.156 10 false 2 4.51,2.833 4.719,3.094 0.208,0.26 10 false 3 4.531,3.542 4.802,3.698 0.271,0.156 10 false n2 4.531,3.75 6.688,4.094 2.156,0.344 10 false No. 2 Rear Seat Leg Assembly RH 2.354,2.958 2.646,3.24 0.292,0.281 10 false T6 2.333,2.76 2.677,2.99 0.344,0.229 10 false 12 1.948,2.969 2.323,3.125 0.375,0.156 10 false SG1


PROCEDURE

1.CHECK FOLDING MOTOR OPERATION
a.

Check folding motor operation.


Result:
Result Proceed to
OK A
NG (LH seat does not operate) B
NG (RH seat does not operate) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT REAR NO. 2 SEAT LEG ASSEMBLY LH

C

4.INSPECT REAR NO. 2 SEAT LEG ASSEMBLY RH
2.INSPECT REAR NO. 2 SEAT LEG ASSEMBLY LH

OK

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR NO. 2 SEAT LEG ASSEMBLY LH)

NG

REPLACE REAR NO. 2 SEAT LEG ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR NO. 2 SEAT LEG ASSEMBLY LH)
a.

Disconnect the T6 and T8 fold seat control ECU connectors.


b.

Disconnect the m2 rear No. 2 seat leg assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T8,m2,T6)Location & Routing

Click Connector(T8)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

Click Connector(m2)Body>No. 2 Rear Seat Wire RH>Rear Power Seat Slide Motor RH

Click Connector(T6)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

T8-6 (FLD+) - m2-4 Always Below 1 Ω
T8-6 (FLD+) or m2-4 - Body ground Always 10 kΩ or higher
T8-7 (FLD-) - m2-1 Always Below 1 Ω
T8-7 (FLD-) or m2-1 - Body ground Always 10 kΩ or higher
T6-10 (SFLD) - m2-2 Always Below 1 Ω
T6-10 (SFLD) or m2-2 - Body ground Always 10 kΩ or higher
T6-12 (SG1) - m2-3 Always Below 1 Ω
T6-12 (SG1) or m2-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR NO. 2 SEAT LEG ASSEMBLY RH

OK

5.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR NO. 2 SEAT LEG ASSEMBLY RH)

NG

REPLACE REAR NO. 2 SEAT LEG ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR NO. 2 SEAT LEG ASSEMBLY RH)
a.

Disconnect the T6 and T7 fold seat control ECU connectors.


b.

Disconnect the n2 rear No. 2 seat leg assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T7,n2,T6)Location & Routing

Click Connector(T7)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

Click Connector(n2)Body>No. 2 Rear Seat Wire LH>Rear Power Seat Slide Motor LH

Click Connector(T6)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

T7-3 (FLD+) - n2-4 Always Below 1 Ω
T7-3 (FLD+) or n2-4 - Body ground Always 10 kΩ or higher
T7-6 (FLD-) - n2-1 Always Below 1 Ω
T7-6 (FLD-) or n2-1 - Body ground Always 10 kΩ or higher
T6-11 (SFLD) - n2-2 Always Below 1 Ω
T6-11 (SFLD) or n2-2 - Body ground Always 10 kΩ or higher
T6-12 (SG1) - n2-3 Always Below 1 Ω
T6-12 (SG1) or n2-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR