Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM38G0E _58 Vehicle Interior _100628 SEAT _0467518 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Rear Power Seat Switch Circuit  


DESCRIPTION

When the rear power seat switch is operated, a recline signal is sent to the fold seat control ECU. The ECU activates the power seat motor based on the signal from the rear power seat switch.

WIRING DIAGRAM

for LH Seat


C457098E03
5.01,2.198 6.688,2.531 1.677,0.333 10 false Fold Seat Control ECU 5.25,0.656 5.698,0.865 0.448,0.208 10 false RCLF 5.281,1.375 5.75,1.552 0.469,0.177 10 false RCLR 2.625,0.74 2.969,0.906 0.344,0.167 10 false FWD 2.563,1.479 2.969,1.625 0.406,0.146 10 false BACK 1.688,1.104 1.802,1.26 0.115,0.156 10 false E 5.01,1.979 5.313,2.271 0.302,0.292 10 false T5 3.052,0.51 3.146,0.667 0.094,0.156 10 false 4 1.521,2.031 3.385,2.292 1.865,0.26 10 false Rear Power Seat Switch LH 4.958,1.271 5.281,1.615 0.323,0.344 10 false 3 4.938,0.51 5.219,0.781 0.281,0.271 10 false 13 3.052,1.26 3.271,1.5 0.219,0.24 10 false 1 1.51,0.885 1.604,1.042 0.094,0.156 10 false 3 1.521,1.875 2.396,2.042 0.875,0.167 10 false U9


for RH Seat


C457098E04
5.01,2.198 6.688,2.531 1.677,0.333 10 false Fold Seat Control ECU 5.25,0.656 5.698,0.865 0.448,0.208 10 false RCLF 5.281,1.375 5.75,1.552 0.469,0.177 10 false RCLR 2.625,0.74 2.969,0.906 0.344,0.167 10 false FWD 2.563,1.479 2.969,1.625 0.406,0.146 10 false BACK 1.688,1.104 1.802,1.26 0.115,0.156 10 false E 5.01,1.979 5.313,2.271 0.302,0.292 10 false T5 3.052,0.51 3.146,0.667 0.094,0.156 10 false 4 1.521,2.031 3.365,2.302 1.844,0.271 10 false Rear Power Seat Switch RH 4.958,1.271 5.281,1.615 0.323,0.344 10 false 4 4.938,0.51 5.219,0.781 0.281,0.271 10 false 14 3.052,1.26 3.271,1.5 0.219,0.24 10 false 1 1.51,0.885 1.604,1.042 0.094,0.156 10 false 3 1.521,1.875 2.396,2.042 0.875,0.167 10 false R4


PROCEDURE

1.CHECK RECLINING OPERATION
a.

Check reclining operation.


Result:
Result Proceed to
OK A
NG (LH seat does not operate) B
NG (RH seat does not operate) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT REAR POWER SEAT SWITCH LH

C

4.INSPECT REAR POWER SEAT SWITCH RH
2.INSPECT REAR POWER SEAT SWITCH LH

OK

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR POWER SEAT SWITCH LH)

NG

REPLACE REAR POWER SEAT SWITCH LH

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR POWER SEAT SWITCH LH)
a.

Disconnect the T5 fold seat control ECU connector.


b.

Disconnect the U9 rear power seat switch LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T5,U9)Location & Routing

Click Connector(T5)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

Click Connector(U9)Body>No. 2 Room Wire>Rear Power Seat Switch LH

T5-13 (RCLF) - U9-4 (FWD) Always Below 1 Ω
T5-13 (RCLF) or U9-4 (FWD) - Body ground Always 10 kΩ or higher
T5-3 (RCLR) - U9-1 (BACK) Always Below 1 Ω
T5-3 (RCLR) or U9-1 (BACK) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR POWER SEAT SWITCH RH

OK

5.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR POWER SEAT SWITCH RH)

NG

REPLACE REAR POWER SEAT SWITCH RH

5.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR POWER SEAT SWITCH RH)
a.

Disconnect the T5 fold seat control ECU connector.


b.

Disconnect the R4 rear power seat switch RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T5,R4)Location & Routing

Click Connector(T5)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

Click Connector(R4)Body>Room Wire>Rear Power Seat Switch RH

T5-14 (RCLF) - R4-4 (FWD) Always Below 1 Ω
T5-14 (RCLF) or R4-4 (FWD) - Body ground Always 10 kΩ or higher
T5-4 (RCLR) - R4-1 (BACK) Always Below 1 Ω
T5-4 (RCLR) or R4-1 (BACK) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR