Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2021.04–2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Radio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area

*1: w/ Audio and Visual Sysem (for Radio and Display Type, except 12.3 Inch Display)

*2: w/ Audio and Visual Sysem (for Radio and Display Type, for 12.3 Inch Display)

Radio Receiver Assembly Communication Stop Mode Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Radio and display receiver assembly*1 or radio receiver assembly*2 branch wire or connector

·

Power source circuit of radio and display receiver assembly*1 or radio receiver assembly*2

·

Radio and display receiver assembly*1 or radio receiver assembly*2 ground circuit

·

Radio and display receiver assembly*1 or radio receiver assembly*2



WIRING DIAGRAM

w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display)
C459013E03
4.938,5.063 6.667,5.479 1.729,0.417 10 false Radio and Display Receiver Assembly 5.656,0.417 6.271,0.615 0.615,0.198 10 false CANH 5.646,0.927 6.26,1.125 0.615,0.198 10 false CANL 5.646,1.854 6.26,2.052 0.615,0.198 10 false +B1 5.635,4.635 6.25,4.833 0.615,0.198 10 false GND1 5.667,3.927 6.281,4.125 0.615,0.198 10 false IG 5.656,2.865 6.271,3.063 0.615,0.198 10 false ACC1 5.302,0.406 5.917,0.604 0.615,0.198 10 false I12 5.302,0.938 5.917,1.135 0.615,0.198 10 false I12 5.313,1.854 5.927,2.052 0.615,0.198 10 false I10 5.281,2.865 5.896,3.063 0.615,0.198 10 false I10 5.292,3.896 5.906,4.094 0.615,0.198 10 false I12 5.292,4.625 5.906,4.823 0.615,0.198 10 false I10 5.313,0.208 5.573,0.406 0.26,0.198 10 false 13 5.333,4.417 5.49,4.615 0.156,0.198 10 false 1 5.292,3.677 5.594,3.885 0.302,0.208 10 false 19 5.302,2.656 5.594,2.854 0.292,0.198 10 false 15 5.333,1.656 5.49,1.854 0.156,0.198 10 false 4 5.302,0.729 5.542,0.927 0.24,0.198 10 false 14 1.542,0.302 2.375,0.51 0.833,0.208 10 false 5*1, 4*2 1.542,0.813 2.438,1.083 0.896,0.271 10 false 16*1, 15*2 0.094,1.49 2.563,1.979 2.469,0.49 10 false No. 6 Global CAN Junction Connector*1, No. 9 Global CAN Junction Connector*2 3.25,4.063 4.365,4.406 1.115,0.344 10 false ECU-IGR NO.2 1.031,3.906 2.406,4.156 1.375,0.25 10 false from IGR-NO.2 Relay 1.573,1.823 3.031,2.063 1.458,0.24 10 false from Battery 1.333,2.833 2.542,3.135 1.208,0.302 10 false from ACC Relay 3.365,3.01 4.479,3.354 1.115,0.344 10 false ECU-ACC 3.438,2.021 4.552,2.365 1.115,0.344 10 false RADIO 0.115,1.323 1.24,1.646 1.125,0.323 10 false I167*1, I120*2 0.167,4.313 1.063,4.583 0.896,0.271 10 false *1: for LHD 0.156,4.677 1.052,4.948 0.896,0.271 10 false *2: for RHD 0.313,2.333 2.365,2.552 2.052,0.219 10 false from Engine Stop and Start ECU 0.323,3.344 2.375,3.563 2.052,0.219 10 false from Engine Stop and Start ECU 0.146,5.042 2.385,5.229 2.24,0.188 10 false *3: w/o Stop and Start System 0.146,5.396 2.385,5.583 2.24,0.188 10 false *4: w/ Stop and Start System 4.083,1.75 4.333,1.969 0.25,0.219 10 false *3 4.073,2.229 4.323,2.448 0.25,0.219 10 false *4 4.115,2.75 4.365,2.969 0.25,0.219 10 false *3 4.083,3.219 4.333,3.438 0.25,0.219 10 false *4

w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)
C435704E20
5.281,5.042 7.01,5.458 1.729,0.417 10 false Radio Receiver Assembly 5.688,0.427 6.302,0.625 0.615,0.198 10 false CANH 5.677,0.938 6.292,1.135 0.615,0.198 10 false CANL 5.646,1.854 6.26,2.052 0.615,0.198 10 false +B1 5.635,4.635 6.25,4.833 0.615,0.198 10 false GND1 5.667,3.76 6.281,3.958 0.615,0.198 10 false IG 5.656,2.833 6.271,3.031 0.615,0.198 10 false ACC1 5.302,0.406 5.917,0.604 0.615,0.198 10 false I13 5.302,0.927 5.917,1.125 0.615,0.198 10 false I13 5.313,1.865 5.927,2.063 0.615,0.198 10 false I11 5.292,2.813 5.906,3.01 0.615,0.198 10 false I11 5.292,3.75 5.906,3.948 0.615,0.198 10 false I13 5.292,4.625 5.906,4.823 0.615,0.198 10 false I11 5.313,0.208 5.573,0.406 0.26,0.198 10 false 13 5.333,4.417 5.49,4.615 0.156,0.198 10 false 1 5.313,3.542 5.615,3.75 0.302,0.208 10 false 19 5.302,2.604 5.594,2.802 0.292,0.198 10 false 15 5.333,1.656 5.49,1.854 0.156,0.198 10 false 4 5.302,0.729 5.542,0.927 0.24,0.198 10 false 14 1.542,0.302 2.375,0.51 0.833,0.208 10 false 5*1, 4*2 1.542,0.813 2.438,1.083 0.896,0.271 10 false 16*1, 15*2 0.167,1.49 2.635,2.083 2.469,0.594 10 false No. 6 Global CAN Junction Connector*1, No. 9 Global CAN Junction Connector*2 3.25,3.948 4.365,4.292 1.115,0.344 10 false ECU-IGR NO.2 1.031,3.771 2.406,4.021 1.375,0.25 10 false from IGR-NO.2 Relay 1.552,1.854 3.01,2.094 1.458,0.24 10 false from Battery 1.333,2.833 2.542,3.135 1.208,0.302 10 false from ACC Relay 3.365,3.01 4.479,3.354 1.115,0.344 10 false ECU-ACC 3.438,2.042 4.552,2.385 1.115,0.344 10 false RADIO 0.156,1.323 1.344,1.563 1.188,0.24 10 false I167*1, I120*2 0.396,4.573 1.292,4.844 0.896,0.271 10 false *1: for LHD 0.396,5.021 1.292,5.292 0.896,0.271 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display) A
w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display) B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)

B

4.CHECK FOR OPEN IN CAN BUS WIRE (RADIO RECEIVER ASSEMBLY BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I12 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I12)Location & Routing

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

I12-13 (CANH) - I12-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the I12 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I10)Location & Routing

Click Connector(I10)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

I10-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Start and Start System

*2: w/ Start and Start System

Click Location & Routing(I10,I12)Location & Routing

Click Connector(I10)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

I10-4 (+B1) - Body ground Always 11 to 14 V*1
10.5 to 16 V*2
I10-15 (ACC1) - Body ground Ignition switch ACC 11 to 14 V*1
10.5 to 16 V*2
I12-19 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (+B1, ACC1 terminal) (w/ Stop and Start System) B
·

NG (w/o Stop and Start System)

·

NG (Other terminal) (w/o Stop and Start System)


C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FOR OPEN IN CAN BUS WIRE (RADIO RECEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I13 radio receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-13 (CANH) - I13-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the I11 radio receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I11)Location & Routing

Click Connector(I11)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I11-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR