Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Rear Television Camera Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Rear Television Camera Communication Stop Mode Communication stop for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Rear television camera assembly branch wire or connector

·

Power source circuit of rear television camera assembly

·

Rear television camera assembly ground circuit

·

Rear television camera assembly



WIRING DIAGRAM

C459017E01
4.104,5.865 6.521,6.104 2.417,0.24 10 false *1: w/o Multi-terrain Monitor System 4.104,6.302 6.708,6.563 2.604,0.26 10 false *2: w/ Multi-terrain Monitor System 0.281,1.563 0.74,1.76 0.458,0.198 10 false Q63 0.302,3.625 0.76,3.823 0.458,0.198 10 false I18 0.208,5.802 0.667,6 0.458,0.198 10 false I131 4.917,3.885 7.063,4.156 2.146,0.271 10 false Rear Television Camera Assembly 0.198,5.99 2.583,6.208 2.385,0.219 10 false Parking Assist ECU*2 0.292,3.813 1.958,4.125 1.667,0.313 10 false Multi-display Assembly*1 0.271,1.74 2.813,1.979 2.542,0.24 10 false No. 12 Global CAN Junction Connector 1.271,2.781 1.729,2.979 0.458,0.198 10 false CA+ 1.167,3.365 1.625,3.563 0.458,0.198 10 false CGND 1.177,5.563 1.635,5.76 0.458,0.198 10 false CGND 1.26,4.99 1.719,5.188 0.458,0.198 10 false CB+ 5.615,2.792 6.073,2.99 0.458,0.198 10 false CB+ 5.615,3.365 6.073,3.563 0.458,0.198 10 false CGND 5.656,1.219 6.115,1.417 0.458,0.198 10 false CANL 5.656,0.729 6.115,0.927 0.458,0.198 10 false CANH 4.885,0.521 5.042,0.719 0.156,0.198 10 false 4 5.313,0.521 5.469,0.719 0.156,0.198 10 false 1 4.906,2.615 5.063,2.813 0.156,0.198 10 false 6 4.906,3.188 5.063,3.385 0.156,0.198 10 false 5 1.688,0.625 1.844,0.823 0.156,0.198 10 false 5 1.667,1.177 1.865,1.385 0.198,0.208 10 false 11 1.698,2.708 1.948,2.906 0.25,0.198 10 false 10 1.698,3.292 1.948,3.49 0.25,0.198 10 false 21 1.719,4.917 1.969,5.115 0.25,0.198 10 false 2 1.719,5.49 1.969,5.688 0.25,0.198 10 false 1 2.292,2.719 2.521,2.896 0.229,0.177 10 false *1 2.292,3.302 2.521,3.479 0.229,0.177 10 false *1 2.26,4.896 2.49,5.073 0.229,0.177 10 false *2 2.26,5.51 2.49,5.688 0.229,0.177 10 false *2 4.854,0.719 5.177,0.906 0.323,0.188 10 false g9 4.854,1.292 5.177,1.479 0.323,0.188 10 false g9 4.854,2.802 5.177,2.99 0.323,0.188 10 false g9 4.844,3.375 5.167,3.563 0.323,0.188 10 false g9 5.24,0.729 5.563,0.917 0.323,0.188 10 false g18 5.229,1.292 5.552,1.479 0.323,0.188 10 false g18 5.229,2.813 5.552,3 0.323,0.188 10 false g18 5.229,3.375 5.552,3.563 0.323,0.188 10 false g18 4.885,1.104 5.042,1.302 0.156,0.198 10 false 1 5.292,1.115 5.448,1.313 0.156,0.198 10 false 2 5.302,2.604 5.458,2.802 0.156,0.198 10 false 4 5.302,3.188 5.458,3.385 0.156,0.198 10 false 3 4.833,0.938 5.063,1.115 0.229,0.177 10 false *1 5.271,0.938 5.5,1.115 0.229,0.177 10 false *2 4.844,3.021 5.073,3.198 0.229,0.177 10 false *1 5.25,3.021 5.479,3.198 0.229,0.177 10 false *2 4.854,3.583 5.083,3.76 0.229,0.177 10 false *1 5.25,3.583 5.479,3.76 0.229,0.177 10 false *2 4.844,1.51 5.073,1.688 0.229,0.177 10 false *1 5.271,1.5 5.5,1.677 0.229,0.177 10 false *2

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (REAR TELEVISION CAMERA ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the g9*1 or g18*2 rear television camera assembly connector.

*1: w/o Multi-terrain Monitor System

*2: w/ Multi-terrain Monitor System



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Multi-terrain Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(g9)Location & Routing

Click Connector(g9)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g9-4 (CANH) - g9-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/ Multi-terrain Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(g18)Location & Routing

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g18-1 (CANH) - g18-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Multi-terrain Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(g9)Location & Routing

Click Connector(g9)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g9-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

w/ Multi-terrain Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(g18)Location & Routing

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g18-3 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Multi-terrain Monitor System
Tester Connection Switch Condition Specified Condition

Click Location & Routing(g9)Location & Routing

Click Connector(g9)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g9-6 (CB+) - Body ground Ignition switch ON 5.5 to 7.05 V

w/ Multi-terrain Monitor System
Tester Connection Switch Condition Specified Condition

Click Location & Routing(g18)Location & Routing

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g18-4 (CB+) - Body ground Ignition switch ON 5.5 to 7.05 V



Result:
Result Proceed to
OK A
NG (w/o Panoramic View Monitor System) B
NG (w/ Panoramic View Monitor System) C



A

B

3.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - MULTI-DISPLAY ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - PARKING ASSIST ECU)
3.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
a.

Disconnect the I18 multi-display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g9,I18)Location & Routing

Click Connector(g9)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

g9-6 (CB+) - I18-10 (CA+) Always Below 1 Ω
g9-5 (CGND) - I18-21 (CGND) Always Below 1 Ω
g9-6 (CB+) or I18-10 (CA+) - Body ground Always 10 kΩ or higher
g9-5 (CGND) or I18-21 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the I131 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g18,I131)Location & Routing

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

Click Connector(I131)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

g18-4 (CB+) - I131-2 (CB+) Always Below 1 Ω
g18-3 (CGND) - I131-1 (CGND) Always Below 1 Ω
g18-4 (CB+) or I131-2 (CB+) - Body ground Always 10 kΩ or higher
g18-3 (CGND) or I131-1 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR