Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Stabilizer Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Stabilizer Control ECU Communication Stop Mode Communication stop for "Front Active Stabilizer" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Stabilizer control ECU branch wire or connector

·

Power source circuit of stabilizer control ECU

·

Stabilizer control ECU ground circuit

·

Stabilizer control ECU



WIRING DIAGRAM

C458991E02
0.229,1.25 0.844,1.448 0.615,0.198 10 false Q64 0.229,1.417 1.927,1.854 1.698,0.438 10 false No.13 Global CAN Junction Connector 1.698,2.021 3.135,2.219 1.438,0.198 10 false from IGR NO.4 Relay 4.083,1.865 4.74,2.052 0.656,0.188 10 false STB-IGR 5.635,0.438 6.156,0.615 0.521,0.177 10 false CANH 5.635,1.021 6.156,1.198 0.521,0.177 10 false CANL 5.635,2.031 5.958,2.198 0.323,0.167 10 false IGB 5.635,3.156 6.021,3.344 0.385,0.188 10 false GND 5.323,3.813 5.938,4.01 0.615,0.198 10 false Q14 5.323,3.99 6.875,4.177 1.552,0.188 10 false Stabilizer Control ECU 1.688,0.927 2,1.125 0.313,0.198 10 false 15 1.719,0.333 2.031,0.531 0.313,0.198 10 false 4 5.406,0.333 5.615,0.521 0.208,0.188 10 false 8 5.406,0.906 5.615,1.094 0.208,0.188 10 false 7 5.417,1.906 5.625,2.094 0.208,0.188 10 false 1 5.417,3.063 5.625,3.25 0.208,0.188 10 false 4

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STABILIZER CONTROL ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the Q14 stabilizer control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q14)Location & Routing

Click Connector(Q14)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Stabilizer Control ECU

Q14-8 (CANH) - Q14-7 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q14)Location & Routing

Click Connector(Q14)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Stabilizer Control ECU

Q14-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q14)Location & Routing

Click Connector(Q14)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Stabilizer Control ECU

Q14-1 (IGB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE STABILIZER CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR