| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B1AAE71 | Front Door Left Speaker Circuit Actuator Stuck | When the stereo component equalizer assembly detects the front door left speaker connection malfunction for 1 second or more continuously 3 seconds after the ignition switch is turned to ACC |
·
Harness or connector
·
Front No. 1 Speaker Assembly LH
·
Front No. 3 Speaker Assembly LH*
·
Stereo component equalizer assembly |
Active Noise Control | A |
*: for 4 or 6 Speakers
| Proceed to |
|---|
| NEXT |
NEXT
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for 2 Speakers | A |
| for 4 or 6 Speakers | B |
A
B
Pre-procedure1
Disconnect the S25 stereo component equalizer assembly connector.
Disconnect the N7 front No. 1 speaker assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S25,N7)Location & Routingewd_type=routing;type=c,c;code=S25,N7 Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assemblyewd_type=component;type=c;code=S25;pinno=13,28 Click Connector(N7)Body>Front Door Wire LH>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=N7;pinno=2,1 |
||
| S25-13 (FL+) - N7-2 (+) | Always | Below 1 Ω |
| S25-28 (FL-) - N7-1 (-) | Always | Below 1 Ω |
| S25-13 (FL+) - Body ground | Always | 10 kΩ or higher |
| S25-28 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the S25 stereo component equalizer assembly connector.
Disconnect the L3 front No. 3 speaker assembly LH connector.
Disconnect the N7 front No. 1 speaker assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S25,L3,N7)Location & Routingewd_type=routing;type=c,c,c;code=S25,L3,N7 Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assemblyewd_type=component;type=c;code=S25;pinno=13,28 Click Connector(L3)Instrument Panel>No. 4 Instrument Panel Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=L3;pinno=4,2,3,1 Click Connector(N7)Body>Front Door Wire LH>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=N7;pinno=2,1 |
||
| S25-13 (FL+) - L3-4 (+) | Always | Below 1 Ω |
| S25-28 (FL-) - L3-2 (-) | Always | Below 1 Ω |
| L3-3 (TWL+) - N7-2 (+) | Always | Below 1 Ω |
| L3-1 (TWL-) - N7-1 (-) | Always | Below 1 Ω |
| S25-13 (FL+) - Body ground | Always | 10 kΩ or higher |
| S25-28 (FL-) - Body ground | Always | 10 kΩ or higher |
| L3-3 (TWL+) - Body ground | Always | 10 kΩ or higher |
| L3-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Replace the front No. 3 speaker assembly LH with a new or known good one.
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B