Home › Audio / Visual / Telematics › AUDIO / VIDEO › ACTIVE NOISE CONTROL SYSTEM (for Type B)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467500 ACTIVE NOISE CONTROL SYSTEM(for Type B) C

AUDIO / VIDEO  ACTIVE NOISE CONTROL SYSTEM(for Type B)  B1AB171  Rear Subwoofer Speaker Circuit Actuator Stuck  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1AB171 Rear Subwoofer Speaker Circuit Actuator Stuck When the stereo component equalizer assembly detects the rear subwoofer speaker connection malfunction for 1 second or more continuously 3 seconds after the ignition switch is turned to ACC
·

Harness or connector

·

No. 1 speaker with box assembly

·

Stereo component equalizer assembly


Active Noise Control A

WIRING DIAGRAM

E455915E05
1.375,1.448 3.625,1.698 2.25,0.25 10 false No. 1 Speaker with Box Assembly 4.792,1.917 5.198,2.083 0.406,0.167 10 false S25 1.365,1.26 1.771,1.427 0.406,0.167 10 false T15 5.26,0.573 5.594,0.74 0.333,0.167 10 false RL+ 5.26,0.958 5.594,1.125 0.333,0.167 10 false RL- 1.75,0.542 2.271,0.74 0.521,0.198 10 false WF1+ 4.958,0.469 5.198,0.646 0.24,0.177 10 false 11 4.958,0.865 5.198,1.031 0.24,0.167 10 false 26 2.271,0.479 2.417,0.646 0.146,0.167 10 false 2 2.26,0.865 2.406,1.031 0.146,0.167 10 false 1 4.802,2.104 6.583,2.49 1.781,0.385 10 false Stereo Component Equalizer Assembly 1.781,0.927 2.302,1.125 0.521,0.198 10 false WF1-

PROCEDURE

1.CLEAR DTC
Body Electrical > Active Noise Control > Clear DTCs
50002 415
Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
Body Electrical > Active Noise Control > Trouble Codes
50001 415
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - NO. 1 SPEAKER WITH BOX ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - NO. 1 SPEAKER WITH BOX ASSEMBLY)

Pre-procedure1

a.

Disconnect the S25 stereo component equalizer assembly connector.


b.

Disconnect the T15 No. 1 speaker with box assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S25,T15)Location & Routing

Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

Click Connector(T15)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>No. 1 Speaker with Box Assembly

S25-11 (RL+) - T15-2 (WF1+) Always Below 1 Ω
S25-26 (RL-) - T15-1 (WF1-) Always Below 1 Ω
S25-11 (RL+) - Body ground Always 10 kΩ or higher
S25-26 (RL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY

OK

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY

NG

REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY