Home › Engine / Hybrid System › V35A-FTS (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL
RM38G0E _51 Engine / Hybrid System _100652 V35A-FTS ENGINE MECHANICAL _0467572 FRONT CRANKSHAFT OIL SEAL A

V35A-FTS ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A485361N01
2.385,4.052 2.708,4.271 0.323,0.219 2.333,4 2.76,4.323 0.427,0.323 6.51,0.552 6.854,0.552 false 4.781,3.313 5.229,4.104 5.229,4.104 5.417,4.104 false 2.542,4.052 2.542,3.677 false 2.271,1.698 2.677,1.698 false 3.906,3.677 4.375,4.5 4.375,4.5 4.563,4.5 false 6.531,0.156 6.875,0.156 false 6.021,0 6.521,0.292 0.5,0.292 18 false 5, 6 6.313,0.385 6.51,0.688 0.198,0.302 18 false 3 2.729,1.563 2.927,1.865 0.198,0.302 18 false 4 4.906,4.365 5.104,4.667 0.198,0.302 18 false 2 5.938,3.958 6.135,4.26 0.198,0.302 18 false 1 2.427,4.073 2.688,4.292 0.26,0.219 10 false *T1 5.771,4.01 5.927,4.208 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 TIMING CHAIN CASE OIL SEAL 11301C (Click here) - -
2 CRANKSHAFT PULLEY 13471 (Click here) - -
3 ADD ENGINE OIL - - (Click here) -
4 RADIATOR ASSEMBLY 16400 - - -
5 INSPECT ENGINE OIL LEVEL - (Click here) - -
6 INSPECT FOR OIL LEAK - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V100135

MP grease - -
*T1 1st: 120 (1224, 89)
2nd: 365 (3722, 269)
- -

PROCEDURE

Hide 11301C 1.INSTALL TIMING CHAIN CASE OIL SEAL

a.
A482291C01
6.573,0.719 6.635,0.438 6.635,0.438 6.781,0.438 true 4.229,1.729 3.688,1.646 3.688,1.646 3.542,1.646 true 4.5,1.833 4.5,2.365 4.5,2.365 4.26,2.365 true 6.125,0.865 6.063,0.635 6.063,0.635 5.948,0.635 true 5.948,1.229 6.229,1.229 false 0.927,0.583 1.115,0.906 0.188,0.323 18 false i 3.104,0.031 3.677,0.313 0.573,0.281 18 false ii - iv 3.354,1.552 3.542,1.75 0.188,0.198 10 false *1 6.823,0.344 7.01,0.542 0.188,0.198 10 false *2 5.76,1.135 5.948,1.333 0.188,0.198 10 false *3 6.219,0.26 6.406,0.458 0.188,0.198 10 false *a 3.938,2.281 4.26,2.479 0.323,0.198 10 false SST 5.635,0.552 5.958,0.75 0.323,0.198 10 false SST
*1 Crankshaft Pulley Set Bolt *2 Timing Chain or Belt Cover Sub-assembly
*3 Timing Chain Case Oil Seal - -
*a Oil Seal Protrusion Height - -


i.

Apply MP grease to the lip of a new timing chain case oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the timing chain case oil seal.

·

Do not allow MP grease to contact the dust seal.




ii.

Install the timing chain case oil seal to SST.

SST
09223-51010  


iii.

Set SST and the crankshaft pulley set bolt as shown in the illustration.

HINT:

Make sure to leave the crankshaft pulley set bolt screwed into the crankshaft by 2 or 3 threads.



iv.

Using SST and the crankshaft pulley set bolt, evenly tap in the timing chain case oil seal until its surface is flush with the end face of the timing chain or belt cover sub-assembly.

Oil Seal Protrusion Height:

0 to 0.5 mm (0 to 0.0197 in.)


NOTICE:
·

Do not tap the timing chain case oil seal at an angle.

·

Keep the lip free of foreign matter.





Hide 13471 2.INSTALL CRANKSHAFT PULLEY

a.
A482292C01
2.333,2 2.333,2.375 2.333,2.375 2.635,1.927 true 0.854,0.052 1.417,0.375 0.563,0.323 18 false i - iii 2.219,2.417 2.542,2.615 0.323,0.198 10 false SST 1.51,0.5 1.75,0.719 0.24,0.219 10 false *a
*a Hold - -
V100135

Turn - -


i.

Align the crankshaft timing gear key with the key groove of the crankshaft pulley, and slide on the crankshaft pulley.


ii.

Step 1:

Using SST, tighten the crankshaft pulley set bolt.

SST
09213-58014  (09213-70020)
09330-00021  

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


iii.

Step 2:

Tighten the crankshaft pulley set bolt.

Torque:
365 N*m (3722 kgf*cm, 269 ft.*lbf)



Hide 16400 4.INSTALL RADIATOR ASSEMBLY