Home › Engine / Hybrid System › V35A-FTS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM38G0E _51 Engine / Hybrid System _100652 V35A-FTS ENGINE MECHANICAL _0467573 REAR CRANKSHAFT OIL SEAL A

V35A-FTS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A488662N01
5.479,1.365 5.813,1.583 0.333,0.219 5.438,1.323 5.854,1.625 0.417,0.302 4.281,2.385 4.729,1.479 4.729,1.479 5.094,1.479 false 5.708,2.5 5.948,2.167 5.948,2.167 6.198,2.167 false 1.875,1.25 2.281,0.438 2.281,0.438 2.594,0.438 false 2.542,1.396 2.833,0.833 2.833,0.833 3.042,0.833 false 3.26,1.542 3.406,1.25 3.406,1.25 3.552,1.25 false 3.396,2.76 3.604,2.76 3.604,2.76 3.865,2.271 false 6.49,0.219 6.823,0.219 false 3.188,2.667 3.396,2.865 0.208,0.198 10 false *1 3.083,0.292 3.281,0.583 0.198,0.292 18 false 1 3.396,0.688 3.594,0.979 0.198,0.292 18 false 2 3.885,1.094 4.135,1.406 0.25,0.313 18 false 3 6.25,2.01 6.448,2.302 0.198,0.292 18 false 5 5.156,1.385 5.469,1.583 0.313,0.198 10 false ●★ 4.375,2.333 4.719,2.542 0.344,0.208 10 false x 10 5.979,0.063 6.469,0.365 0.49,0.302 18 false 4, 6 5.531,1.385 5.823,1.604 0.292,0.219 10 false *T1 2.917,0.344 3.073,0.542 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR ENGINE OIL SEAL 11381A (Click here) - -
2 NO. 1 CRANKSHAFT POSITION SENSOR PLATE 19315 (Click here) - -
3 INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 32101 (Click here) - -
4 INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 32101 (Click here) - -
5 AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY - - - -
6 INSPECT FOR OIL LEAK - (Click here) - -

*1 REAR DRIVE PLATE SPACER - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V100135

MP grease
V100136

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
★ Precoated part - -
*T1 1st: 29.5 (301, 22)
2nd: Turn 90°
- -

PROCEDURE

Hide 11381A 1.INSTALL REAR ENGINE OIL SEAL

a.
A482297C01
1.146,0.531 1.594,0.854 0.448,0.323 18 false i, ii 3.51,0.052 3.771,0.385 0.26,0.333 18 false iii 4.542,1.75 4.75,1.969 0.208,0.219 10 false *a
*a Oil Seal Protrusion Height - -


i.

Clean the oil seal retainer oil seal contact surface of the crankshaft.


ii.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the timing chain case oil seal.

·

Do not allow MP grease to contact the dust seal.




iii.

Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-56010  

Oil Seal Protrusion Height:

0 to 0.5 mm (0 to 0.0197 in.)


NOTICE:
·

Do not tap the rear engine oil seal at an angle.

·

Keep the lip free of foreign matter.





Hide 19315 2.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A482299C01
3.302,0.833 3.635,0.292 3.635,0.292 3.844,0.292 true 1.698,1.865 1.875,1.865 1.875,1.865 2.208,0.823 true 3.875,0.198 4.073,0.406 0.198,0.208 10 false *b 1.5,1.76 1.698,1.969 0.198,0.208 10 false *a 0.938,0.052 1.219,0.406 0.281,0.354 18 false i
*a Pin Hole *b Pin
V100135

Engine Front - -


i.

Install the crankshaft angle sensor rotor.

HINT:

Align the pin hole of the crankshaft angle sensor rotor with the pin of the crankshaft.




Hide 32101 3.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A485362C01
1.208,5.198 1.208,4.74 true 4.542,2.052 4.969,2.052 false 5.396,2.635 5.552,2.719 5.552,2.719 5.552,2.948 false 1.708,2.073 1.708,2.542 1.708,2.542 2.073,2.01 true 3.146,4.51 3.323,4.51 3.323,4.51 3.563,4.833 true 0.448,0.083 0.698,0.385 0.25,0.302 18 false i 4.177,0.104 4.396,0.396 0.219,0.292 18 false ii 0.417,3.531 0.99,3.833 0.573,0.302 18 false iii, iv 2.688,3.542 3.417,3.854 0.729,0.313 18 true v - viii 4.875,4.594 5.083,4.792 0.208,0.198 10 true 10 5.333,3.885 5.458,4.083 0.125,0.198 10 true 1 5.448,4.885 5.573,5.083 0.125,0.198 10 true 2 4.917,4.281 5.042,4.479 0.125,0.198 10 true 3 5.865,4.448 5.99,4.646 0.125,0.198 10 true 4 5.188,4.854 5.313,5.052 0.125,0.198 10 true 5 5.615,3.938 5.74,4.135 0.125,0.198 10 true 6 5.719,4.781 5.844,4.979 0.125,0.198 10 true 7 5.115,3.969 5.24,4.167 0.125,0.198 10 true 8 5.833,4.198 5.958,4.396 0.125,0.198 10 true 9 5.49,2.969 5.677,3.167 0.188,0.198 10 false *2 4.354,1.958 4.542,2.156 0.188,0.198 10 false *1 1.135,5.208 1.323,5.406 0.188,0.198 10 false *a 4.333,2.646 4.521,2.844 0.188,0.198 10 false *b 1.583,2.573 1.938,2.781 0.354,0.208 10 false SST 2.438,4.875 2.625,5.073 0.188,0.198 10 false *c 2.969,4.417 3.156,4.615 0.188,0.198 10 false *d 4.031,4.521 4.219,4.719 0.188,0.198 10 false *e
*1 Drive Plate and Ring Gear Sub-assembly *2 Rear Drive Plate Spacer
*a Adhesive *b Engine Front
*c Up *d Paint Mark
*e 90° - -


i.

Using SST, hold the crankshaft pulley.

SST
09213-58014  (09213-70020)
09330-00021  


ii.

Install the drive plate and ring gear sub-assembly and rear drive plate spacer onto the crankshaft.

HINT:

As the drive plate and ring gear sub-assembly and the rear drive plate spacer are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.



iii.

Clean the 10 bolt holes.


iv.

Apply a few drops of adhesive to 2 or 3 threads at the tip of each of 10 new bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

After applying the adhesive, tighten the bolt right away.



v.

Install and uniformly tighten the 10 bolts in the sequence shown in the illustration.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Do not reuse the drive plate installation bolts.

·

Handle the drive plate installation bolts carefully. Do not scratch them or subject them to any shocks.

·

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.




vi.

Mark the top of the bolts with paint.


vii.

Tighten the 10 bolts 90° in the same sequence.


viii.

Check that the paint marks are now at a 90° angle to the top.



Hide 32101 4.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 5.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY