Home › Engine / Hybrid System › V35A-FTS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM38G0E _51 Engine / Hybrid System _100652 V35A-FTS ENGINE MECHANICAL _0467573 REAR CRANKSHAFT OIL SEAL A

V35A-FTS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A482293N01
4.281,2.417 4.771,1.573 4.771,1.573 5.021,1.573 false 5.823,2.583 6.063,2.25 6.063,2.25 6.313,2.25 false 1.906,1.281 2.229,0.719 2.229,0.719 2.406,0.719 false 2.521,1.396 2.667,1.167 2.667,1.167 2.875,1.167 false 3.26,1.563 3.49,1.083 3.49,1.083 3.635,1.083 false 3.385,2.771 3.594,2.771 3.594,2.771 3.854,2.281 false 3.177,2.667 3.385,2.865 0.208,0.198 10 false *1 6.354,2.083 6.552,2.375 0.198,0.292 18 false 1 3.958,0.948 4.156,1.24 0.198,0.292 18 false 2 2.917,1.021 3.115,1.313 0.198,0.292 18 false 3 2.917,0.573 3.115,0.865 0.198,0.292 18 false 4 5.073,1.469 5.385,1.667 0.313,0.198 10 false ●★ 4.417,2.354 4.76,2.563 0.344,0.208 10 false x 10 2.76,0.625 2.917,0.823 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY - - - -
2 DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 32101 (Click here) - -
3 NO. 1 CRANKSHAFT POSITION SENSOR PLATE 19315 - - -
4 REAR ENGINE OIL SEAL 11381A (Click here) - -

*1 REAR DRIVE PLATE SPACER - -
● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear engine oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Automatic transmission assembly ECU configuration - (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
Automatic transmission fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)

PROCEDURE

Hide 1.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY

Hide 32101 2.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A482294N01
1.646,1.958 1.646,2.375 1.646,2.375 2.031,1.917 true 4.198,0.073 4.417,0.385 0.219,0.313 18 false ii 0.417,0.031 0.635,0.344 0.219,0.313 18 false i 1.5,2.406 1.823,2.604 0.323,0.198 10 false SST

i.

Using SST, hold the crankshaft pulley.

SST
09213-58014  (09213-70020)
09330-00021  


ii.

Remove the 10 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly, and crankshaft angle sensor rotor.



Hide 19315 3.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A488661


Hide 11381A 4.REMOVE REAR ENGINE OIL SEAL

a.
A482296C01
3.021,1.625 2.844,1.625 2.844,1.625 2.615,1.271 true 3.188,0.521 3.354,0.521 3.354,0.521 3.469,0.875 true 1.844,0.042 2.292,0.354 0.448,0.313 18 false i, ii 3.042,1.521 3.292,1.771 0.25,0.25 10 true *b 2.969,0.417 3.177,0.625 0.208,0.208 10 true *a
*a Protective Tape *b Cut Position


i.

Using a knife, cut through the lip of the rear engine oil seal.


ii.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

After removal, check the crankshaft for damage.

If it is damaged, smooth the surface with 400-grit sandpaper.


HINT:

Tape the screwdriver tip before use.