| *A | w/ Cover | - | - |
| *1 | OVERFLOW PLUG | *2 | REFILL PLUG |
| *3 | NO. 1 TRANSMISSION OIL FILLER TUBE | *4 | FILLER PLUG |
| *5 | DRAIN PLUG | - | - |
| ● | Non-reusable part | - | - |
| *1 | NO. 3 ENGINE MOUNTING HOLE COVER | - | - |
| *a | Black: x 1 Silver: x 5 |
- | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission assembly removal/installation are shown below.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
| *a | Object Exceeding Weight Limit of Transmission Jack |
The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
37140 1.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
37110F 2.REMOVE REAR PROPELLER SHAFT ASSEMBLY
17500 3.REMOVE CONVERTER ASSEMBLY LH WITH CATALYST
17400M 4.REMOVE CONVERTER ASSEMBLY RH WITH CATALYST
28100 5.REMOVE STARTER ASSEMBLY
w/ Stop and Start System:
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>STARTER (w/ Stop And Start System)>REMOVAL
w/o Stop and Start System:
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>STARTER (w/o Stop And Start System)>REMOVAL
51470 6.REMOVE TRANSMISSION UNDER COVER ASSEMBLY (w/ Cover)
7.DRAIN AUTOMATIC TRANSMISSION FLUID
36336 8.REMOVE TRANSFER HEAT INSULATOR
36179 9.REMOVE LOWER TRANSFER CASE PROTECTOR
10.DRAIN TRANSFER OIL
17119 11.REMOVE NO. 2 MANIFOLD STAY
11363A 12.REMOVE FLYWHEEL HOUSING SIDE COVER
32101A 13.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT
Remove the 6 drive plate and torque converter setting bolts from the drive plate and ring gear sub-assembly.
Turn the crankshaft to a position where the drive plate and torque converter setting bolts can be removed, and remove the drive plate and torque converter setting bolts while securing the crankshaft pulley bolt with a wrench.
14.DISCONNECT OIL COOLER TUBE SUB-ASSEMBLY
35979B 15.REMOVE TRANSMISSION INSULATOR RH
33825 16.REMOVE TRANSMISSION CONTROL CABLE INSULATOR
33823 18.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
19.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY
Using a transmission jack and a belt sling, etc., support the automatic transmission assembly with transfer assembly.
Using a belt sling, etc., secure the automatic transmission assembly with transfer assembly to the transmission jack to prevent it from falling.
20.REMOVE NO. 3 FRAME CROSSMEMBER ASSEMBLY
21.DISCONNECT WIRE HARNESS CLAMP BRACKET
36407 22.DISCONNECT TRANSFER BREATHER HOSE SUB-ASSEMBLY
|
|
23.DISCONNECT WIRE HARNESS
|
|
| *a | Transmission Wire Connector | *b | TCM connector |
|
Connector |
|
Bolt |
|
Pull Down the Lever |
|
While Pressing the Lock |
|
Pull Up the Lever | - | - |
Disconnect the 5 connectors.
Disconnect the claw, pull down the lever, and then disconnect the transmission wire connector.
Disconnect the TCM connector lever while pressing the lever lock as shown in the illustration.
Detach the clamp.
Remove the 5 bolts and disconnect the wire harness from the automatic transmission assembly with transfer assembly.
24.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY
|
|
Remove the 11 bolts and automatic transmission assembly with transfer assembly.
Do not use excessive force to pry out the automatic transmission assembly with transfer assembly when separating it from the engine assembly to prevent the knock pins from being damaged.
When removing the automatic transmission assembly with transfer assembly, make sure that the oil cooler tube does not become damaged.
12371A 25.REMOVE REAR ENGINE MOUNTING INSULATOR
36100 26.REMOVE TRANSFER ASSEMBLY
Remove the 8 bolts and transfer assembly from the automatic transmission assembly.
Check the center of gravity while removing the transfer assembly.
Do not drop the transfer assembly.
27.REMOVE EXHAUST SENSOR CLAMP BRACKET
| *A | for LH Side | *B | for RH Side |
28.REMOVE WIRE HARNESS CLAMP BRACKET
32000 29.REMOVE TORQUE CONVERTER ASSEMBLY
| *a | Matchmark | - | - |
Put matchmarks on the automatic transmission assembly with transfer assembly and torque converter assembly.
Remove the torque converter assembly from the automatic transmission assembly with transfer.