CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
|
*: w/ Washer Nozzle Heater System |
|||
| A-22 (CXPI) - Body ground | CXPI communication line | Ignition switch ON | Pulse generation |
| I1-15 (WHTR) - Body ground* | Washer nozzle heater relay (WSH NZL HTR) operation signal | Ignition switch ON, washer nozzle heater system not operating | 11 to 14 V |
| Ignition switch ON, washer nozzle heater system operating | Below 1 V | ||
| I3-6 (WPS) - Body ground | Windshield wiper relay (WIPER) operation signal | Ignition switch ON | 11 to 14 V |
| Less than approximately 60 seconds after ignition switch off | |||
| Approximately 60 seconds or more after ignition switch off | Below 1 V | ||
| I3-11 (RWRY) - Body ground | Rear wiper motor assembly operation signal | Rear wiper motor assembly stopped | 11 to 14 V |
| Rear wiper motor assembly operating | Below 1 V | ||
CHECK WINDSHIELD WIPER RELAY ASSEMBLY
Disconnect the I95 and I94 windshield wiper relay assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I95-3 (E) - Body ground | Ground | Always | Below 1 Ω |
| I95-5 (EWS) - Body ground | Ground | Always | Below 1 Ω |
| I95-6 (IGWS) - Body ground | Washer circuit IG power source | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | ||
| I95-8 (+B) - Body ground | Ignition switch signal (Power source circuit) | Ignition switch ON | 11 to 14 V |
| Less than approximately 60 seconds after ignition switch off | |||
| Approximately 60 seconds or more after ignition switch off | Below 1 V | ||
| I94-5 (ES) - Body ground | Ground | Always | Below 1 Ω |
Connect the I95 and I94 windshield wiper relay assembly connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I95-1 (+WR) - Body ground | Front washer operation signal | Ignition switch ON, front washer operating | 11 to 14 V |
| I95-2 (+1) - Body ground | LO operation signal to windshield wiper motor assembly | Ignition switch ON, windshield wiper motor assembly operating in LO | 11 to 14 V |
| I95-4 (+2) - Body ground | HI operation signal to windshield wiper motor assembly | Ignition switch ON, windshield wiper motor assembly operating in HI | 11 to 14 V |
| I95-7 (-WR) - Body ground | Rear washer operation signal | Ignition switch ON, rear washer operating | 11 to 14 V |
| I94-3 (2S) - Body ground | Windshield wiper motor assembly HI operation signal | Windshield wiper motor assembly stopped | 4.5 to 5.5 V |
| Windshield wiper motor assembly operating in LO | 9 to 14 V | ||
| Windshield wiper motor assembly operating in HI | Below 1 V | ||
| I94-4 (MPX1) - Body ground | CXPI communication line | Ignition switch ON | Pulse generation |
| I94-6 (+SM) - Body ground | Windshield wiper motor assembly position detection signal | Windshield wiper motor assembly in LO or HI operation | Below 1 V ←→ 10 to 14 V |
| Windshield wiper motor assembly stopped | Below 1 V |
CHECK RAIN SENSOR (w/ Auto Wiper System)
Disconnect the d23 rain sensor connector.
Measure the voltage and resistance and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| d23-2 (ES) - Body ground | Ground | Always | Below 1 Ω |
| d23-3 (MPX) - Body ground | LIN communication signal | Ignition switch ON | Pulse generation |
| d23-4 (SIG) - Body ground | IG power source circuit | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
HEADLIGHT ECU SUB-ASSEMBLY RH (w/ Headlight Cleaner System with Headlight ECU)
Since the headlight ECU sub-assembly RH uses waterproof connectors, the voltage, resistance and waveform cannot be checked directly. The voltage, resistance and waveform are indicated for reference only.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B7-6 (IGR) - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| B7-7 (HLC) - Body ground | Headlight cleaner motor operation signal | Ignition switch ON, light control switch head and headlight cleaner motor not operating | 11 to 14 V |
| Ignition switch ON, light control switch head and headlight cleaner operating | Below 1 V | ||
| B7-12 (GND) - Body ground | Ground | Always | Below 1 Ω |
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
CHECK SEMICONDUCTOR POWER INTEGRATION ECU
Click herePower Source / Network>POWER DISTRIBUTION>POWER INTEGRATION SYSTEM>TERMINALS OF ECU