Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM38G0E _59 Vehicle Exterior _100456 WIPER / WASHER _0467584 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B127987  Humidity/Rain Sensor Missing Message  


DESCRIPTION

The main body ECU (multiplex network body ECU) and rain sensor communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B127987 Humidity/Rain Sensor Missing Message
DTC Detection Condition:

Ignition switch ON (IG+ voltage 9.5 V or higher)


Malfunction Status:

Communication malfunction with rain sensor


Malfunction Duration:

Continues for 10 seconds or more


·

Rain sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)

·

Map light assembly


○ Main Body B

WIRING DIAGRAM

E466194E01
0.99,0.24 2.354,0.448 1.365,0.208 10 false from IGR-NO.1 Relay 0.74,1.313 1.74,1.542 1,0.229 10 false ECU-IGR NO.1 2.208,2.521 3.031,2.708 0.823,0.188 10 false Rain Sensor 2.208,2.344 2.667,2.542 0.458,0.198 10 false d23 2.083,1.104 2.542,1.302 0.458,0.198 10 false SIG 2.083,1.823 2.396,2.021 0.313,0.198 10 false ES 2.813,1.427 3.271,1.625 0.458,0.198 10 false MPX 1.854,1 2.01,1.198 0.156,0.198 10 false 4 1.854,1.719 2.01,1.917 0.156,0.198 10 false 2 3.24,1.271 3.396,1.469 0.156,0.198 10 false 3 0.625,4.448 2.302,4.646 1.677,0.198 10 false : LIN Communication Line 4.938,1.281 5.25,1.479 0.313,0.198 10 false 11 4.948,2.135 5.26,2.333 0.313,0.198 10 false I2 4.948,2.302 6.615,2.74 1.667,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 5.208,1.417 5.823,1.615 0.615,0.198 10 false LIN4 5.208,3.365 5.823,3.563 0.615,0.198 10 false LIN1 4.927,3.24 5.24,3.438 0.313,0.198 10 false 13 5.073,3.958 5.385,4.156 0.313,0.198 10 false d2 5.094,4.146 6.438,4.375 1.344,0.229 10 false Map Light Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

If DTC B276C88 is output, troubleshoot for DTC B276C88 first.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>B276C88



PROCEDURE

1.CLEAR THE DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT


b.

Turn the ignition switch to ON and wait for at least 10 seconds.



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
B127987 is output. A
B127987 and B276F87 are output. B



A

3.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BATTERY AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - RAIN SENSOR)
3.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the d23 rain sensor connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(d23)Location & Routing

Click Connector(d23)Body>No. 1 Roof Wire>Rain Sensor

d23-4 (SIG) - Body ground Ignition switch off Below 1 V
d23-4 (SIG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d23)Location & Routing

Click Connector(d23)Body>No. 1 Roof Wire>Rain Sensor

d23-2 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - RAIN SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - RAIN SENSOR)

Pre-procedure1

a.

Disconnect the I2 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the d23 rain sensor connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I2,d23)Location & Routing

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

Click Connector(d23)Body>No. 1 Roof Wire>Rain Sensor

I2-11 (LIN4) - d23-3 (MPX) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - RAIN SENSOR)

Pre-procedure1

a.

Disconnect the I2 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the d23 rain sensor connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I2,d23)Location & Routing

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

Click Connector(d23)Body>No. 1 Roof Wire>Rain Sensor

I2-11 (LIN4) - d23-3 (MPX) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR