Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM38G0E _59 Vehicle Exterior _100456 WIPER / WASHER _0467584 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B235787  Wiper Module Missing Message  


DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield wiper relay assembly communicate via CXPI communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B235787 Wiper Module Missing Message
Detection condition:

Battery voltage is 9.5 V or higher


Malfunction Status:

Communication malfunction between the main body ECU (multiplex network body ECU) and windshield wiper relay assembly


Malfunction Time:

10 seconds or more


·

Windshield wiper relay assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

Windshield washer relay (WIPER)


○ Main Body A

WIRING DIAGRAM

B582796E06
0.479,4.552 1.583,5.021 1.104,0.469 10 false Windshield Wiper Relay Assembly 0.781,5.406 2.521,5.646 1.74,0.24 10 false : CXPI Communication Line 1.333,0.99 1.563,1.167 0.229,0.177 10 false +B 1.156,2.844 1.573,3.052 0.417,0.208 10 false MPX1 1.344,4.031 1.594,4.229 0.25,0.198 10 false ES 1.406,3.448 1.563,3.646 0.156,0.198 10 false E 1.698,1 1.948,1.188 0.25,0.188 10 false I95 1.698,2.865 1.958,3.073 0.26,0.208 10 false I94 1.698,4.042 1.99,4.219 0.292,0.177 10 false I94 1.698,3.458 1.938,3.646 0.24,0.188 10 false I95 1.75,0.781 2.063,0.979 0.313,0.198 10 false 8 1.75,2.646 1.906,2.844 0.156,0.198 10 false 4 1.75,3.229 1.906,3.427 0.156,0.198 10 false 3 1.76,3.823 2.073,4.021 0.313,0.198 10 false 5 4.021,1.156 4.792,1.354 0.771,0.198 10 false WIPER 3.583,0.219 4.427,0.469 0.844,0.25 10 false from Battery 5.156,1.333 5.563,1.51 0.406,0.177 10 false I3 5.167,2.865 5.354,3.042 0.188,0.177 10 false A 5.167,1.135 5.479,1.333 0.313,0.198 10 false 6 5.146,2.646 5.51,2.958 0.365,0.313 10 false 22 5.49,1.24 5.948,1.438 0.458,0.198 10 false WPS 5.479,2.833 5.938,3.031 0.458,0.198 10 false CXPI 5.344,4 6.99,4.396 1.646,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 6.083,0.646 6.396,0.844 0.313,0.198 10 false IG 6.438,0.656 6.677,0.875 0.24,0.219 10 false +B 2.344,1.729 3.938,2.135 1.594,0.406 10 false Windshield Washer Relay (WIPER) 2.688,0.885 2.844,1.083 0.156,0.198 10 false 5 2.688,1.229 2.844,1.427 0.156,0.198 10 false 2 3.531,0.896 3.688,1.094 0.156,0.198 10 false 3 3.531,1.229 3.688,1.427 0.156,0.198 10 false 1 3.958,2.865 4.365,3.073 0.406,0.208 10 false 5C 3.969,2.635 4.313,2.844 0.344,0.208 10 false 20 4.24,3.573 5.396,3.969 1.156,0.396 10 false Power Distribution Box Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuse of circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

Pre-procedure1

a.

Disconnect the I94 windshield wiper relay assembly connector.


b.

Disconnect the A main body ECU (multiplex network body ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I94)Location & Routing

Click Connector(I94)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

I94-4 (MPX1) - A-22 (CXPI) Always Below 1 Ω
I94-4 (MPX1) or A-22 (CXPI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Pre-procedure1

B582797C07
1.521,0.323 1.896,0.552 0.375,0.229 0.875,1.385 1.063,1.865 1.063,1.865 1.26,1.865 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.667,0.354 2.125,0.552 0.458,0.198 10 false A 1.365,1.76 1.781,1.969 0.417,0.208 10 false CXPI
*a Component without harness connected
(Main Body ECU [Multiplex Network Body ECU])


a.

Disconnect the main body ECU (multiplex network body ECU) connector.


Procedure1

b.

Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-22 (CXPI) - Body ground Ignition switch off Below 1 V
A-22 (CXPI) - Body ground Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

3.PERFORM ACTIVE TEST USING GTS (WIPER POWER RELAY)

NG

3.PERFORM ACTIVE TEST USING GTS (WIPER POWER RELAY)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wiper Power Relay Operates the windshield wiper relay (WIPER) OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Wiper Power Relay
50004 449 70
OK:

Windshield wiper relay (WIPER) operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

NG

9.INSPECT WINDSHIELD WASHER RELAY (WIPER)
4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the I94 and I95 windshield wiper relay assembly connectors.


Procedure1


Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BATTERY)

Pre-procedure1

a.

Disconnect the I95 windshield wiper relay assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I95)Location & Routing

Click Connector(I95)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

I95-8 (+B) - Body ground Ignition switch ON 11 to 14 V
I95-8 (+B) - Body ground Less than approximately 60 seconds after ignition switch turned off 11 to 14 V
I95-8 (+B) - Body ground Approximately 60 seconds or more after ignition switch turned off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

6.INSPECT WINDSHIELD WASHER RELAY (WIPER)
6.INSPECT WINDSHIELD WASHER RELAY (WIPER)

OK

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WIPER] - BATTERY)

NG

REPLACE WINDSHIELD WASHER RELAY (WIPER)

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WIPER] - BATTERY)

Pre-procedure1

a.
B472073C10
0.094,0.042 0.406,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Windshield Washer Relay [WIPER])


Remove the windshield washer relay (WIPER) from the No. 1 engine room relay block assembly.


b.

Disconnect the I95 windshield wiper relay assembly connector.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Windshield washer relay (WIPER) terminal 3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WIPER] - WINDSHIELD WIPER RELAY ASSEMBLY BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WIPER] - WINDSHIELD WIPER RELAY ASSEMBLY BODY GROUND)

Pre-procedure1

a.

Remove the windshield washer relay (WIPER) from the No. 1 engine room relay block assembly.


b.

Disconnect the I95 windshield wiper relay assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I95)Location & Routing

Click Connector(I95)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Windshield Wiper Relay Assembly

I95-8 (+B) - Windshield washer relay (WIPER) terminal 5 Always Below 1 Ω
I95-8 (+B) or Windshield washer relay (WIPER) terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT WINDSHIELD WASHER RELAY (WIPER)

OK

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WIPER] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE WINDSHIELD WASHER RELAY (WIPER)

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WIPER] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

Pre-procedure1

a.

Remove the windshield washer relay (WIPER) from the No. 1 engine room relay block assembly.


b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I3)Location & Routing

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

Windshield washer relay (WIPER) terminal 1 - I3-6 (WPS) Always Below 1 Ω
Windshield washer relay (WIPER) terminal 1 or I3-6 (WPS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

11.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WIPER] - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WIPER] - BODY GROUND)

Pre-procedure1

a.
B472073C11
0.094,0.042 0.406,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Windshield Washer Relay [WIPER])


Remove the windshield washer relay (WIPER) from the No. 1 engine room relay block assembly.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Windshield washer relay (WIPER) terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR