Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST ECU (for LHD)
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0467783 PARKING ASSIST ECU(for LHD) A

PARK ASSIST / MONITORING  PARKING ASSIST ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B594952N01
4.813,1.719 4.979,1.385 4.979,1.385 5.313,1.385 false 2.417,0.823 2.583,0.49 2.583,0.49 2.917,0.49 false 5.365,1.219 5.646,1.573 0.281,0.354 18 false 1 2.958,0.313 3.24,0.667 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -
2 ECU WITH PARKING ASSIST ECU - - - -

B594886N01
3.594,0.083 6.052,1.354 2.458,1.271 3.26,2 3.583,1.833 3.583,1.833 4,1.833 false 4.948,0.99 5.271,0.823 5.271,0.823 5.688,0.823 false 5.75,0.656 6.031,1.01 0.281,0.354 18 false 3 4.073,1.656 4.354,2.01 0.281,0.354 18 false 4 3.646,0.146 4.021,0.385 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

3 DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY 85970A - - -
4 PARKING ASSIST ECU 86792C - - -

*A w/ Double Locking System - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the parking assist ECU assembly removal/ installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Parking assist ECU
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 73900 1.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 2.REMOVE ECU WITH PARKING ASSIST ECU

HINT:

The illustration is an example, so the details may differ.


a.
B594865


Hide 85970A 3.REMOVE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Double Locking System)

a.
B594877


Hide 86792C 4.REMOVE PARKING ASSIST ECU

a.
B594878