ADJUST PANORAMIC VIEW MONITOR SYSTEM
If any of the work in the following table has been performed, perform registration of the panoramic view monitor system.
If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.
Work performed during servicing may require the registration and initialization of the panoramic view monitor system and other systems.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Conduct the pre-work checks (Procedure 1) before performing screen adjustment.
PROCEDURE 1: PRE-WORK CHECKS
Preliminary checks
Provide shadow to prevent backlight from hitting the camera.
Use string that does not stretch.
Apply pieces of adhesive tape to serve as check markers. When placing the markers, make them 100 mm (3.94 in.) wide.
SST may also be used for the recognition markers and the positioning and check markers used in optical axis adjustment.
Perform the work in a wide, level location (L direction approximately 6.5 m x W direction approximately 3.5 m).
Park the vehicle on a flat surface with the steering wheel centered.
Before stopping the vehicle, move the vehicle backward and forward to ensure that both the steering wheel and the tires point straight ahead.
Adjust the tire pressure to the specified value(s).
Remove all luggage from the vehicle and place the markers before starting work.
Marker locations (check marker)
Secure the string to the locations required to make the checks and set markers as shown in the illustration.
| *a | Cross Check Marker |
| *b | Check Marker |
| *c | String 1 |
| *d | String 2 |
| *e | String 3 |
Front camera adjustment only
| *a | Cross Check Marker |
| *b | Check Marker |
| *c | String 1 |
| *d | String 2 |
| *e | String 4 |
Rear camera adjustment only
| *a | Cross Check Marker |
| *b | Check Marker |
| *c | String 1 |
| *d | String 2 |
| *e | String 3 |
| *f | String 4 |
| *g | String 5 |
Left camera adjustment only
| *a | Cross Check Marker |
| *b | Check Marker |
| *c | String 1 |
| *d | String 2 |
| *e | String 3 |
| *f | String 4 |
| *g | String 6 |
Right camera adjustment only
Adjustment of 4 cameras
| *a | Cross Check Marker | *b | Check Marker |
| *c | String 1 | *d | String 2 |
| *e | String 3 | *f | String 4 |
| *g | String 5 | *h | String 6 |
Marker positions
Set the check markers at the positions shown in the illustration.
| *a | 4200 mm (13.8 ft.) | *b | 2400 mm (7.87 ft.) |
| *c | 1500 mm (4.92 ft.) | *d | 693 mm (2.27 ft.) |
| *e | 400 mm (1.31 ft.) | *f | 600 mm (1.97 ft.) |
| *g | 2300 mm (7.54 ft.) | *h | 2500 mm (8.20 ft.) |
PROCEDURE 2: SET DATUM POINTS
Extend the datum line (string 1).
| *a | Mark A |
| *b | Weight |
Hang a weight with a pointed tip and accurately mark the center position on the road surface. (Mark A)
Make sure that the weight hangs straight down from the string.
Close the rear door before hanging the string.
Repeat the procedure to mark the right side. (Mark B)
| *a | String 1 |
| *b | Mark A |
| *c | Mark B |
Secure string 1 so that it passes through marks A and B on the left and right sides.
When securing the string, check that there is no slack and the string is not twisted.
Extend the vehicle center line (string 2).
Hang a weight with a pointed tip such that is passes through the center of the front television camera assembly and accurately mark the center position on the road surface. (Mark C)
| *1 | Front Television Camera Assembly | - | - |
| *a | Center Point | *b | Weight |
| *c | String | *d | Mark C |
Hang a weight with a pointed tip from the center of the rear emblem and accurately mark the center position on the road surface. (Mark D)
| *a | Center | *b | Weight |
| *c | String | *d | Mark D |
| *e | Equal Distance to Center | - | - |
| *a | Datum Point |
| *b | String 1 |
| *c | String 2 |
| *d | Mark C |
| *e | Mark D |
Secure string 2 so that it passes through marks C and D at the front and rear of the vehicle.
When securing string, check that there is no slack and the string is not twisted.
Set the point where strings 1 and 2 intersect as the datum point.
PROCEDURE 3: SET MARKERS (FRONT ADJUSTMENT)
| *a | 4200 mm (13.8 ft.) |
| *b | Datum Point |
| *c | String 1 |
| *d | String 2 |
| *e | Mark E |
In front of the vehicle, extend string (3) perpendicular to the vehicle center line (string (2)), and place a marker.
Mark the position on string 2 in front of the vehicle, 4200 mm (13.8 ft.) from the datum point. (Mark E)
| *a | 400 mm (1.31 ft.) |
| *b | String 2 |
| *c | Mark E |
Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.
Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)
| *a | 800 mm (2.62 ft.) String | *b | String 2 |
| *c | Mark E | *d | Mark F |
| *e | Mark G | - | - |
| *a | 1500 mm (4.92 ft.) |
| *b | String 2 |
| *c | String 3 |
| *d | Mark F |
| *e | Mark G |
| *f | Mark H |
| *g | Mark I |
Secure string (3) so that it passes through marks F and G as shown in the illustration.
When securing the string, check that there is no slack and the string is not twisted.
Mark positions on string (3), 1500 mm (4.92 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I).
| *a | 800 mm (2.62 ft.) |
| *b | 100 mm (0.33 ft.) |
| *c | Cross Check Marker |
| *d | Check Marker |
| *e | String 1 |
| *f | Mark F |
| *g | Mark G |
| *h | Mark H |
| *i | Mark I |
Place and secure the cross check markers, centered on marks H and I.
Align the cross check markers perpendicular to the string.
Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.
Place the check marker between marks F and G.
Perform the screen adjustment procedure (procedure 9).
PROCEDURE 4: SET MARKERS (REAR ADJUSTMENT)
To the rear of the vehicle, extend string (4) perpendicular to the vehicle center line (string (2)), and place a check marker.
| *a | 2400 mm (7.87 ft.) |
| *b | Datum Point |
| *c | String 1 |
| *d | String 2 |
| *e | Mark J |
Mark a position on string 2 to the rear of the vehicle, 2400 mm (7.87 ft.) from the datum point. (Mark J)
| *a | 400 mm (1.31 ft.) |
| *b | String 1 |
| *c | String 2 |
| *d | Mark J |
Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.
Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)
| *a | 800 mm (2.62 ft.) String | *b | String 1 |
| *c | String 2 | *d | Mark J |
| *e | Mark K | *f | Mark L |
| *a | 1500 mm (4.92 ft.) |
| *b | String 2 |
| *c | String 4 |
| *d | Mark K |
| *e | Mark L |
| *f | Mark M |
| *g | Mark N |
Secure string (4) so that it passes through marks K and L as shown in the illustration.
When securing the string, check that there is no slack and the string is not twisted.
Mark positions on string (4), 1500 mm (4.92 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)
| *a | 800 mm (2.62 ft.) |
| *b | 100 mm (0.33 ft.) |
| *c | 400 mm (1.31 ft.) |
| *d | Cross Check Marker |
| *e | Check Marker |
| *f | String 1 |
| *g | Mark K |
| *h | Mark L |
| *i | Mark M |
| *j | Mark N |
Place and secure the cross check markers, centered on marks M and N.
Align the cross check markers perpendicular to the string.
Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.
Extend the rear cross check markers to string 1.
Place the check marker between marks K and L.
Perform the screen adjustment procedure (procedure 9).
PROCEDURE 5: SET MARKERS (LEFT-SIDE ADJUSTMENT)
At the left side of the vehicle, extend string (5) parallel to the vehicle center line (string (2)), and place a marker
| *a | 2400 mm (7.87 ft.) |
| *b | 4200 mm (13.8 ft.) |
| *c | Datum Point |
| *d | String 1 |
| *e | String 2 |
| *f | Mark E |
| *g | Mark J |
Mark the position on string (2) in front of the vehicle, 4200 mm (13.8 ft.) from the datum point. (Mark E)
Mark the position on string (2) to the rear of the vehicle, 2400 mm (7.87 ft.) from the datum point. (Mark J)
| *a | 400 mm (1.31 ft.) |
| *b | String 2 |
| *c | Mark E |
Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.
Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)
| *a | 800 mm (2.62 ft.) String | *b | String 2 |
| *c | Mark E | *d | Mark F |
| *e | Mark G | - | - |
| *a | 400 mm (1.31 ft.) |
| *b | String 1 |
| *c | String 2 |
| *d | Mark J |
Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.
Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)
| *a | 800 mm (2.62 ft.) String | *b | String 1 |
| *c | String 2 | *d | Mark J |
| *e | Mark K | *f | Mark L |
| *a | 1500 mm (4.92 ft.) |
| *b | String 2 |
| *c | String 3 |
| *d | String 4 |
| *e | Mark F |
| *f | Mark G |
| *g | Mark H |
| *h | Mark K |
| *i | Mark L |
| *j | Mark M |
Secure strings (3) and (4) so that they pass through marks F and G, marks K and L as shown in the illustration.
When securing the string, check that there is no slack and the string is not twisted.
Mark strings (3) and (4), 1500 mm (4.92 ft.) to the left of the vehicle center line (string 2). (Marks H and M)
| *a | String 1 |
| *b | String 2 |
| *c | String 3 |
| *d | String 4 |
| *e | String 5 |
| *f | Mark H |
| *g | Mark M |
Secure string (5) so that it passes through marks H and M as shown in the illustration.
When securing the string, check that there is no slack and the string is not twisted.
| *a | 400 mm (1.31 ft.) |
| *b | 600 mm (1.97 ft.) |
| *c | 2300 mm (7.54 ft.) |
| *d | 2500 mm (8.20 ft.) |
| *e | String 1 |
| *f | String 5 |
| *g | Mark H |
| *h | Mark M |
| *i | Mark O |
| *j | Mark P |
| *k | Mark Q |
| *l | Mark R |
Make marks on string (5) that are 400 mm (1.31 ft.), 600 mm (1.97 ft.), 2300 mm (7.54 ft.) and 2500 mm (8.20 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)
| *a | 100 mm (0.33 ft.) |
| *b | 800 mm (2.62 ft.) |
| *c | 400 mm (1.31 ft.) |
| *d | Cross Check Marker |
| *e | Check Marker |
| *f | String 1 |
| *g | String 5 |
| *h | Mark H |
| *i | Mark M |
| *j | Mark O |
| *k | Mark P |
| *l | Mark Q |
| *m | Mark R |
Place and secure the cross check markers, centered on marks H and M.
Align the cross check markers perpendicular to the string.
Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.
Extend the rear cross check markers to string 1.
Place check markers between marks O and P, and marks Q and R.
Perform the screen adjustment procedure (procedure 9).
PROCEDURE 6: SET MARKERS (RIGHT-SIDE ADJUSTMENT)
At the right side of the vehicle, extend string (6) parallel to the vehicle center line (string (2)), and place a marker.
| *a | 2400 mm (7.87 ft.) |
| *b | 4200 mm (13.8 ft.) |
| *c | Datum Point |
| *d | String 1 |
| *e | String 2 |
| *f | Mark E |
| *g | Mark J |
Mark the position on string (2) in front of the vehicle, 4200 mm (13.8 ft.) from the datum point. (Mark E)
Mark the position on string (2) to the rear of the vehicle, 2400 mm (7.87 ft.) from the datum point. (Mark J)
| *a | 400 mm (1.31 ft.) |
| *b | String 2 |
| *c | Mark E |
Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.
Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)
| *a | 800 mm (2.62 ft.) String | *b | String 2 |
| *c | Mark E | *d | Mark F |
| *e | Mark G | - | - |
| *a | 400 mm (1.31 ft.) |
| *b | String 1 |
| *c | String 2 |
| *d | Mark J |
Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.
Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)
| *a | 800 mm (2.62 ft.) String | *b | String 1 |
| *c | String 2 | *d | Mark J |
| *e | Mark K | *f | Mark L |
| *a | 1500 mm (4.92 ft.) |
| *b | String 2 |
| *c | String 3 |
| *d | String 4 |
| *e | Mark F |
| *f | Mark G |
| *g | Mark I |
| *h | Mark K |
| *i | Mark L |
| *j | Mark N |
Secure strings (3) and (4) so that they pass through marks F and G and marks K and L as shown in the illustration.
When securing the string, check that there is no slack and the string is not twisted.
Mark strings (3) and (4), 1500 mm (4.92 ft.) to the right of the vehicle center line (string 2). (Marks I and N)
| *a | String 1 |
| *b | String 2 |
| *c | String 3 |
| *d | String 4 |
| *e | String 6 |
| *f | Mark I |
| *g | Mark N |
Secure string (6) so that it passes through marks I and N as shown in the illustration.
When securing the string, check that there is no slack and the string is not twisted.
| *a | 400 mm (1.31 ft.) |
| *b | 600 mm (1.97 ft.) |
| *c | 2300 mm (7.54 ft.) |
| *d | 2500 mm (8.20 ft.) |
| *e | String 1 |
| *f | String 6 |
| *g | Mark I |
| *h | Mark N |
| *i | Mark S |
| *j | Mark T |
| *k | Mark U |
| *l | Mark V |
Make marks on string (6) that are 400 mm (1.31 ft.), 600 mm (1.97 ft.), 2300 mm (7.54 ft.) and 2500 mm (8.20 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)
| *a | 100 mm (0.33 ft.) |
| *b | 800 mm (2.62 ft.) |
| *c | 400 mm (1.31 ft.) |
| *d | Cross Check Marker |
| *e | Check Marker |
| *f | String 1 |
| *g | String 6 |
| *h | Mark I |
| *i | Mark N |
| *j | Mark S |
| *k | Mark T |
| *l | Mark U |
| *m | Mark V |
Place and secure the cross check markers, centered on marks I and N.
Align the cross check markers perpendicular to the string.
Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.
Extend the rear cross check markers to string 1.
Place check markers between marks S and T, and marks U and V.
Perform the screen adjustment procedure (procedure 9).
PROCEDURE 7: SET MARKERS (ADJUSTMENT OF ALL CAMERAS)
At the right and left sides of the vehicle, extend strings (5) and (6) parallel to the vehicle center line (string 2), and place markers.
| *a | 2400 mm (7.87 ft.) |
| *b | 4200 mm (13.8 ft.) |
| *c | Datum Point |
| *d | String 1 |
| *e | String 2 |
| *f | Mark E |
| *g | Mark J |
Mark the position on string (2) in front of the vehicle, 4200 mm (13.8 ft.) from the datum point. (Mark E)
Mark the position on string (2) to the rear of the vehicle, 2400 mm (7.87 ft.) from the datum point. (Mark J)
| *a | 400 mm (1.31 ft.) |
| *b | String 2 |
| *c | Mark E |
Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.
Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)
| *a | 800 mm (2.62 ft.) String | *b | String 2 |
| *c | Mark E | *d | Mark F |
| *e | Mark G | - | - |
| *a | 400 mm (1.31 ft.) |
| *b | String 1 |
| *c | String 2 |
| *d | Mark J |
Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.
Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)
| *a | 800 mm (2.62 ft.) String | *b | String 1 |
| *c | String 2 | *d | Mark J |
| *e | Mark K | *f | Mark L |
| *a | 1500 mm (4.92 ft.) |
| *b | String 2 |
| *c | String 3 |
| *d | String 4 |
| *e | Mark F |
| *f | Mark G |
| *g | Mark H |
| *h | Mark I |
| *i | Mark K |
| *j | Mark L |
| *k | Mark M |
| *l | Mark N |
Secure strings (3) and (4) so that they pass through marks F, G, K and L as shown in the illustration.
When securing the string, check that there is no slack and the string is not twisted.
Mark string (3), 1500 mm (4.92 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I)
Mark string (4), 1500 mm (4.92 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)
| *a | String 1 |
| *b | String 2 |
| *c | String 3 |
| *d | String 4 |
| *e | String 5 |
| *f | String 6 |
| *g | Mark H |
| *h | Mark I |
| *i | Mark M |
| *j | Mark N |
Secure strings (5) and (6) so that they pass through marks H, M, I and N as shown in the illustration.
When securing the string, check that there is no slack and the string is not twisted.
| *a | 400 mm (1.31 ft.) |
| *b | 600 mm (1.97 ft.) |
| *c | 2300 mm (7.54 ft.) |
| *d | 2500 mm (8.20 ft.) |
| *e | String 1 |
| *f | String 2 |
| *g | String 3 |
| *h | String 4 |
| *i | String 5 |
| *j | String 6 |
| *k | Mark O |
| *l | Mark P |
| *m | Mark Q |
| *n | Mark R |
| *o | Mark S |
| *p | Mark T |
| *q | Mark U |
| *r | Mark V |
Make marks on string (5) that are 400 mm (1.31 ft.), 600 mm (1.97 ft.), 2300 mm (7.54 ft.) and 2500 mm (8.20 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)
Make marks on string (6) that are 400 mm (1.31 ft.), 600 mm (1.97 ft.), 2300 mm (7.54 ft.) and 2500 mm (8.20 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)
Place and secure the cross check markers, centered on marks H, I, M and N.
Align the cross check markers perpendicular to the string.
Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.
Extend the rear cross check markers to string 1.
| *a | 100 mm (0.33 ft.) | *b | 800 mm (2.62 ft.) |
| *c | Cross Check Marker | *d | Check Marker |
| *e | String 1 | *f | Mark F |
| *g | Mark G | *h | Mark H |
| *i | Mark I | *j | Mark K |
| *k | Mark L | *l | Mark M |
| *m | Mark N | *n | Mark O |
| *o | Mark P | *p | Mark Q |
| *q | Mark R | *r | Mark S |
| *s | Mark T | *t | Mark U |
| *u | Mark V | - | - |
Place check markers between marks F and G, marks K and L, marks O and P, marks Q and R, marks S and T, and marks U and V.
Perform the screen adjustment procedure (procedure 9).
PROCEDURE 8: SET MARKERS (SST ADJUSTMENT)
Using SST (marker tool set), place the markers.
| Part Name | Color | Length | Qty |
|---|---|---|---|
| Marker A | White | 800 mm (31.5 in.) | 6 |
| Marker B | White | 950 mm (37.4 in.) | 2 |
| Marker E | White | 350 mm (13.8 in.) | 6 |
| Marker F | White | 1000 mm (39.4 in.) | 2 |
| Marker G | White | 293 mm (11.5 in.) | 4 |
| Marker H | White | 200 mm (7.87 in.) | 4 |
| Spacer J | Black | 1000 mm (39.4 in.) | 6 |
| Spacer K | Black | 500 mm (19.7 in.) | 2 |
| Spacer M | Black | 307 mm (12.1 in.) | 4 |
| Spacer N | Black | 200 mm (7.87 in.) | 2 |
| Spacer O | Black | 100 mm (3.94 in.) | 4 |
| Marker Q | White | 500 mm (19.7 in.) | 2 |
| *a | Marker A |
| *b | Marker B |
| *c | Marker E |
| *d | Marker F |
| *e | Marker G |
Set the marker A, marker B, marker E, marker F and marker G so as to surround the vehicle as shown in the illustration.
| Part Name | Color | Length | Qty |
|---|---|---|---|
| Marker A | White | 800 mm (31.5 in.) | 6 |
| Marker B | White | 950 mm (37.4 in.) | 2 |
| Marker E | White | 350 mm (13.8 in.) | 6 |
| Marker F | White | 1000 mm (39.4 in.) | 2 |
| Marker G | White | 293 mm (11.5 in.) | 4 |
| *a | Marker Q |
| *b | Marker B |
| *c | Marker F |
Place the marker Q between marker B and marker F as shown in the illustration.
| Part Name | Color | Length | Qty |
|---|---|---|---|
| Marker Q | White | 500 mm (19.7 in.) | 2 |
| *a | Spacer J |
Set the spacer J as shown in the illustration.
| Part Name | Color | Length | Qty |
|---|---|---|---|
| Spacer J | Black | 1000 mm (39.4 in.) | 4 |
| *a | A (Spacer J, Spacer K and Spacer N) |
| *b | B (Spacer M and Spacer O) |
Combine with spacers and set at positions A and B to assemble the marker tool set.
| Part Name | Color | Length | Qty |
|---|---|---|---|
| Spacer J | Black | 1000 mm (39.4 in.) | 1 |
| Spacer K | Black | 500 mm (19.7 in.) | 1 |
| Spacer N | Black | 200 mm (7.87 in.) | 1 |
Create 2 sets and combine together.
| Part Name | Color | Length | Qty |
|---|---|---|---|
| Spacer M | Black | 307 mm (12.1 in.) | 1 |
| Spacer O | Black | 100 mm (3.94 in.) | 1 |
Create 4 sets and combine together.
Set the marker H.
| *a | 100 mm (3.94 in.) | *b | Marker F |
| *c | Marker H | *d | Distance from the front end of the marker F to the rear end of the marker H |
| Marker H Setting Positions | Distance from the front end of the marker F to the rear end of the marker H |
|---|---|
| A | 2300 mm (7.54 ft.) |
| B | 400 mm (1.31 ft.) |
Align the position number on the marker F with the datum line as shown in the illustration.
When aligning the marker F with the datum line, check that the string used for the datum line is not twisted or bent.
| *A | Example | - | - |
| *a | Datum line | *b | Marker F |
| Marker F Position |
|---|
| 1 |
Align the mark-off line of the marker A set at the front and back with the vehicle center line as shown in the illustration.
When aligning the marker A with the vehicle center line, check that the string used for the vehicle center line is not twisted or bent.
| *a | Marker A | *b | Mark-off line |
| *c | Vehicle center line | - | - |
Check that the entire marker tool set is not distorted after the setting is completed. If there is any distortion, perform corrections so that it is straightened.
Perform the screen adjustment procedure (procedure 9).
PROCEDURE 9: CAMERA VIEW ADJUSTMENT (CALIBRATION)
Enter diagnostic mode.
w/ Audio and Visual System:
w/ Navigation System:
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
The check must be performed with the engine started. Therefore, apply the parking brake, depress the brake pedal and move the shift position to P to ensure that the vehicle does not begin moving unexpectedly.
Select "Function Check/Setting" from the "Service Menu" screen.
Select "Camera Setting" on the "Function Check/Setting I" screen.
If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.
Select "View Adjustment" on the "Mode Setting (*)" screen to display the adjustment screen.
To select a grayed out item, select and hold the item for 2 seconds or more.
After checking the screen, press the "Next" button on the "Signal Check (*)" screen.
When "CHK" (red) is displayed, perform the inspections.
If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".
Perform the view adjustment.
| *a | Red Line | *b | Cross Check Marker |
| *c | Adjustment Button | *d | Camera Select Button |
| *e | Height Control Button | - | - |
If replacing a camera, select the repaired camera and press "New Camera".
Check that the cross check markers displayed on the adjustment screen appear connected.
Before checking the adjustment screen, ensure that the check markers have been placed correctly.
If a cross check marker appears displaced on the adjustment screen, use the camera select buttons to select the corresponding camera, and then use the adjustment buttons or vehicle height adjustment buttons to adjust the screen.
If adjustment is needed, select "All View Reset" button and reset all adjustment values.
Confirm the check marker is in the adjustment screen.
Before checking the adjustment screen, ensure that the check markers have been placed correctly.
If a check marker appears displaced on the adjustment screen, use the camera select buttons to select the corresponding camera, and then use the adjustment buttons or vehicle height adjustment buttons to adjust the screen.
If performing adjustment again, select "All View Reset" to initialize the adjustment status.
When all adjustments are completed, press "OK".
If data writing ends normally, "The view data writing was completed." is displayed.
Press "OK".
Finish diagnostic mode.
w/ Audio and Visual System:
w/ Navigation System:
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
PROCEDURE 10: STEERING ANGLE SETTING
Preparation for adjustment
Park the vehicle with the steering wheel centered.
Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
Adjust the tire pressure to the specified value(s).
Start the diagnostic mode.
w/ Audio and Visual System:
w/ Navigation System:
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
The check must be performed with the engine started. Therefore, apply the parking brake, depress the brake pedal and move the shift position to P to ensure that the vehicle does not begin moving unexpectedly.
Select "Function Check/Setting" on the "Service Menu" screen.
Select "Camera Setting" on the "Function Check/Setting I" screen.
If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.
Select "Steering Angle Setting" on the "Mode Setting (*)" screen to display the "Signal Check (*)" screen.
To select a grayed out item, select and hold the item for 2 seconds or more.
Select "Next" on the "Signal Check (*)" screen to display the "Steering Angle Setting D (*)" screen.
If "CHK" (red) is displayed for an item on the Signal Check (*) screen, selecting "Next" will not change to the "Steering Angle Setting D (*)" screen.
Check the "Signal Check (*)" screen when "CHK" (red) is displayed for an item on the "Signal Check (*)" screen.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DIAGNOSIS SYSTEM
Adjust the steering angle.
Check that the steering wheel is centered (approximately +/- 5 degrees or less) and then select "Steering Center Memorize".
Turn the steering wheel fully to the left and fully to the right, and then press "Max Steering Angle Memorize". (Turning right and then left is OK)
When "Max Steering Angle Memorize" is selected, the steering angle setting values (steering neutral point and maximum steering angle) are stored and the system beeps for a long duration to notify the user that storing is complete before the "Mode Setting (*)" screen is displayed again.
A beep will sound to confirm that the adjustment values have been stored.
If all signals are input normally, the "Mode Setting (*)" screen is displayed automatically after the maximum steering angle is stored.
If steering angle setting is incomplete, "OK" cannot be selected.
Even if no DTC is detected, a steering angle sensor malfunction may disable the use of "Max Steering Angle Memorize".
If selecting "Max Steering Angle Memorize" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering angle sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL
Finish diagnostic mode.
w/ Audio and Visual System:
w/ Navigation System:
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Confirm steering angle adjustment.
If the steering angle has been adjusted, confirm the steering angle adjustment on the panoramic view and rear view screen or panoramic view and wide rear view screen after finishing diagnosis mode.
Check on the panoramic view and rear view screen or panoramic view and wide rear view screen that the estimated course line moves until the steering wheel is fully turned to either the left or right.
If the estimated course line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform "Steering Center Memorize" and "Max Steering Angle Memorize" again.
PROCEDURE 11: REAR TELEVISION CAMERA VIEW ADJUSTMENT (for REAR CAMERA DETECTION FUNCTION)
Be sure to check for DTCs before performing this procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
| *a | Vehicle Center |
| *b | Vehicle |
| *c | Front |
| *d | Vehicle End |
| *e | Target Bar for Back Camera Adjustment |
| *f | 1995 to 2005 mm (6.54 to 6.58 ft.) |
| *g | A |
Preparation for adjustment
Park the vehicle with the steering wheel centered.
Set a target bar behind the vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).
Create a target bar for adjustment only when adjusting the optical axis of the rear television camera assembly.
| Area | Specification |
|---|---|
| A | 1000 mm (3.28 ft.) |
Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 100 mm (0.33 ft.) and 1995 to 2005 mm (6.54 to 6.58 ft.), respectively. Check the color on the multi-display and choose a tape color which can be easily seen.
Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
Check that the back door is fully closed.
Start diagnostic mode.
w/ Audio and Visual System:
w/ Navigation System:
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
The check must be performed with the engine started. Therefore, apply the parking brake, depress the brake pedal and move the shift position to P to ensure that the vehicle does not begin moving unexpectedly.
Select "Function Check/Setting" on the "Service Menu" screen.
Select "Camera Setting" on the "Function Check/Setting I" screen.
If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.
Select "Back Camera Setting" on the "Mode Setting (*)" screen.
To select a grayed out item, select and hold the item for 2 seconds or more.
Select "Next" on the "Signal Check (*)" screen.
When "CHK" (red) is displayed for any items on the "Signal Check (*)" screen, selecting "Next" will not change the screen to the "Back Camera Position Setting D (*)" screen.
When "CHK" (red) is displayed for any items on the "Signal Check (*)" screen, perform inspections using the "Signal Check (*)" screen.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DIAGNOSIS SYSTEM
| *a | Target Bar for Back Camera Position Setting |
Back Camera Position Setting (Both Ends of Target Bar)
When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).
Perform vertical and horizontal position adjustment.
Move the circle (A) left, right, up and down by selecting the buttons (C), (D), (E) and (F) so that the left end of target bar for back camera position setting is positioned within the center of the circle (A) (center of the inner red circle).
Perform roll angle adjustment.
Rotate the bar (B) by selecting the buttons (G) or (H) so that the bar (B) becomes parallel to the target bar for back camera position setting.
Select "Next" on the "Back Camera Position Setting D (*)" screen.
| *a | Target Bar for Back Camera Position Setting |
Back Camera Position Setting (Upper Left Corner of Target Bar)
When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).
Perform camera optical axis adjustment (high accuracy adjustment).
Move the adjustment mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the corner of the mark (A) with the upper left corner of the target bar.
The outer corner of the mark (A) is aligned with the upper left corner of the target bar.
| *a | Too Far Inside | *b | Inner Corner Contacting |
| *c | Too Far Outside | - | - |
Select "Next" on the "Back Camera Position Setting D (*) L_TOP" screen.
| *a | Target Bar for Back Camera Position Setting |
Back Camera Position Setting (Lower Left Corner of Target Bar)
When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).
Perform camera optical axis adjustment (high accuracy adjustment).
Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower left corner of the target bar.
The outer corner of the mark (A) is aligned with the lower left corner of the target bar.
| *a | Too Far Inside | *b | Inner Corner Contacting |
| *c | Too Far Outside | - | - |
Select "Next" on the "Back Camera Position Setting D (*) L_BTM" screen.
| *a | Target Bar for Back Camera Position Setting |
Back Camera Position Setting (Upper Right Corner of Target Bar)
When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).
Perform camera optical axis adjustment (high accuracy adjustment).
Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the upper right corner of the target bar.
The outer corner of the mark (A) is aligned with the upper right corner of the target bar.
| *a | Too Far Inside | *b | Inner Corner Contacting |
| *c | Too Far Outside | - | - |
Select "Next" on the "Back Camera Position Setting D (*) R_TOP" screen.
| *a | Target Bar for Back Camera Position Setting |
Back Camera Position Setting (Lower Right Corner of Target Bar)
When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).
Perform camera optical axis adjustment (high accuracy adjustment).
Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower right corner of the target bar.
The outer corner of the mark (A) is aligned with the lower right corner of the target bar.
| *a | Too Far Inside | *b | Inner Corner Contacting |
| *c | Too Far Outside | - | - |
Select "Next" on the "Back Camera Position Setting D (*) R_BTM" screen.
Back Verify Mode
Check that (A) and the target adjustment bar are overlapping.
If the lines are not aligned, perform the "Steering Center Memorize" and "Max Steering Angle Memorize" operations.
If (A) and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the back camera position setting operation.
Select "OK" to return to the "Mode Setting (*)" screen and complete the adjustment.
The update is not completed until "OK" is selected.
When "OK" is selected, a beep will sound to confirm that the adjustment values have been stored.
The adjustment values are not stored until the beep has sounded.
Finish diagnostic mode.
w/ Audio and Visual System:
w/ Navigation System:
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR