| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B00721A | Passenger Seat Belt Pretensioner "A" Deployment Control Circuit Resistance Below Threshold | One of the following conditions is met:
·
The airbag ECU assembly detects a line short in the passenger seat pretensioner squib circuit during for 2 seconds during the primary check.
·
A front seat outer belt assembly RH malfunction (for LHD).
·
A front seat outer belt assembly LH malfunction (for RHD).
·
An airbag ECU assembly malfunction. |
·
Wire harness
·
Front seat outer belt assembly RH (for LHD)
·
Front seat outer belt assembly LH (for RHD)
·
Airbag ECU assembly |
Comes on | SRS Airbag | A | Applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B00721A is output | A |
| Past DTC B00721A is output | B |
Post-procedure1
None
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
To perform the simulation method, enter check mode (signal check) with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the front seat outer belt assembly RH and airbag ECU assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Front Seat Outer Belt Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the front seat outer belt assembly RH connector.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Check that the connectors are not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Front Seat Outer Belt Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *4 | SST |
| *a | Front view of wire harness connector (to Front Seat Outer Belt Assembly RH) |
Connect the Q1 airbag ECU assembly connector.
Connect the white wire side of SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the front seat outer belt assembly RH for measurement, as this may lead to a serious injury due to pretensioner deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B00721A is not output | A |
| DTC B00721A is output | B |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Disconnect SST from connector C.
A
B
Pre-procedure1
| *1 | Front Seat Outer Belt Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector (to Front Seat Outer Belt Assembly RH) |
|
Release the activation prevention mechanism |
Disconnect the Q1 airbag ECU assembly connector.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Q16)Location & Routingewd_type=routing;type=c;code=Q16 |
||
| Q16-1 (R+) - Q16-2 (R-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Restore the released activation prevention mechanism of connector B to the original condition.
OK
NG
| *1 | Front Seat Outer Belt Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Connect the airbag ECU assembly connector.
Connect the front seat outer belt assembly RH connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B00721A is not output | A |
| DTC B00721A is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the simulation method by selecting Check Mode using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
B
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B00721A is output | A |
| Past DTC B00721A is output | B |
Post-procedure1
None
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
To perform the simulation method, enter check mode (signal check) with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the front seat outer belt assembly LH and airbag ECU assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Front Seat Outer Belt Assembly LH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the front seat outer belt assembly LH connector.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Check that the connectors are not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Front Seat Outer Belt Assembly LH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *4 | SST |
| *a | Front view of wire harness connector (to Front Seat Outer Belt Assembly LH) |
Connect the S1 airbag ECU assembly connector.
Connect the white wire side of SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the front seat outer belt assembly LH for measurement, as this may lead to a serious injury due to pretensioner deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B00721A is not output | A |
| DTC B00721A is output | B |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Disconnect SST from connector C.
A
B
Pre-procedure1
| *1 | Front Seat Outer Belt Assembly LH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector (to Front Seat Outer Belt Assembly LH) |
|
Release the activation prevention mechanism |
Disconnect the S1 airbag ECU assembly connector.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S11)Location & Routingewd_type=routing;type=c;code=S11 Click Connector(S11)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Seat Belt Pretensioner LH (Front Seat Outer Belt Assembly LH)ewd_type=component;type=c;code=S11;pinno=1,2 |
||
| S11-1 (L+) - S11-2 (L-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Restore the released activation prevention mechanism of connector B to the original condition.
OK
NG
| *1 | Front Seat Outer Belt Assembly LH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Connect the airbag ECU assembly connector.
Connect the front seat outer belt assembly LH connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B00721A is not output | A |
| DTC B00721A is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the simulation method by selecting Check Mode using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
B