Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100612 SEAT BELT _0468155 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B607703N01
3.208,0.24 4.281,0.917 1.073,0.677 6.104,0.302 6.74,0.302 false 6.094,0.813 6.729,0.813 false 1.51,4.594 1.51,5.031 false 4.01,3.823 4.01,4.26 false 5.958,1.813 6.281,1.813 false 5.927,1.292 6.281,1.292 false 5.281,1.635 5.635,1.635 false 0.813,3.073 1.167,3.073 false 2.042,3.896 2.042,3.573 false 3.177,3.021 3.531,3.021 false 3.146,1.198 3.5,1.198 false 3.823,1.823 4.156,1.823 false 5.135,5.188 5.698,5.188 false 5.906,3.406 6.365,3.406 false 3.583,0.698 3.938,0.698 false 5.875,0.135 6.083,0.458 0.208,0.323 18 false 1 5.865,0.646 6.073,0.969 0.208,0.323 18 false 2 1.448,5.042 1.656,5.365 0.208,0.323 18 false 3 3.958,4.271 4.167,4.594 0.208,0.323 18 false 4 6.542,1.677 6.75,2 0.208,0.323 18 false 5 6.552,1.146 6.76,1.469 0.208,0.323 18 false 6 5.677,1.479 5.875,1.781 0.198,0.302 18 false 7 0.594,2.927 0.792,3.229 0.198,0.302 18 false 8 1.979,3.906 2.177,4.208 0.198,0.302 18 false 9 3.563,2.854 3.938,3.188 0.375,0.333 18 false 10 3.531,1.021 3.906,1.354 0.375,0.333 18 false 11 4.188,1.646 4.563,1.979 0.375,0.333 18 false 12 5.927,5.052 6.302,5.385 0.375,0.333 18 false 13 6.396,3.229 6.771,3.563 0.375,0.333 18 false 14 5.625,2.854 6.083,3.052 0.458,0.198 10 false x 2 2.396,2.031 2.854,2.229 0.458,0.198 10 false x 2 3.979,0.594 4.135,0.792 0.156,0.198 10 false ● 5.688,1.958 6.146,2.156 0.458,0.198 10 false x 2 3.25,0.281 3.625,0.521 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - (Click here) - -
3 FRONT DOOR SCUFF PLATE LH 67914B - - -
4 REAR DOOR SCUFF PLATE LH 67918D - - -
5 ASSIST GRIP PLUG 74617F (Click here) - -
6 ASSIST GRIP PLUG 74617C (Click here) - -
7 REAR ASSIST GRIP ASSEMBLY 74620A - - -
8 OUTER LAP BELT ANCHOR COVER 73233 - - -
9 FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) 73220 - - -
10 CENTER PILLAR LOWER GARNISH LH 62414A - - -
11 CENTER PILLAR GARNISH LH 62412 - - -
12 FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH 73024 - - -
13 FRONT SEAT OUTER BELT ASSEMBLY LH 73220 (Click here) - -
14 FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY 73200A - - -

*A w/ Curtain Shield Airbag - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Parts or Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.

·

Move both front seats to the frontmost position and fold them forward.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B401522

Be sure to read precaution thoroughly before servicing.

(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.






Hide 67914B 3.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67918D 4.REMOVE REAR DOOR SCUFF PLATE LH

Hide 74617F 5.REMOVE ASSIST GRIP PLUG (for Lower Side)

Z101186

(Click here)

Hide 74617C 6.REMOVE ASSIST GRIP PLUG (for Upper Side)

a.

Use the same procedure described for the Lower side.


Hide 74620A 7.REMOVE REAR ASSIST GRIP ASSEMBLY

Hide 73233 8.REMOVE OUTER LAP BELT ANCHOR COVER

a.
B607705


Hide 73220 9.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

a.
B607706


Hide 62414A 10.REMOVE CENTER PILLAR LOWER GARNISH LH

Hide 62412 11.REMOVE CENTER PILLAR GARNISH LH

Hide 73024 12.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

HINT:

Perform this procedure when replacing the front shoulder belt anchor plate sub-assembly LH.


a.
B607707


Hide 73220 13.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B607708C02
2.25,0.229 2.385,0.521 0.135,0.292 18 true i 4.49,0.052 4.677,0.354 0.188,0.302 18 true ii 6.104,1.125 6.302,1.417 0.198,0.292 18 true iii 6.313,1.125 6.656,1.417 0.344,0.292 12 true (*A) 5.667,0.208 5.917,0.5 0.25,0.292 18 true iv 5.521,1.448 5.719,1.75 0.198,0.302 18 true v
*A w/ Tension Reducer - -
V100135

Nut
V100136

Pretensioner Connector
V100137

Tension Reducer Connector
V100138

Bolt


i.

Remove the nut and shoulder anchor of the front seat outer belt assembly LH.


ii.

Disconnect the pretensioner connector.

HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



iii.

w/ Tension Reducer:

1. Disconnect the tension reducer connector.


iv.

Remove the bolt.


v.

Detach the guide and remove the front seat outer belt assembly LH.



Hide 73200A 14.REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

HINT:

Perform this procedure when replacing the front shoulder belt anchor adjuster assembly.


a.
B607709