Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009787  Right Side Restraints Sensor 2 Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009787 Right Side Restraints Sensor 2 Missing Message One of the following conditions is met:
·

The airbag ECU assembly detects a line short in the side collision sensor RH circuit (bus 2) for 2 seconds.

·

The airbag ECU assembly detects a short to ground in the side collision sensor RH circuit (bus 2) for 2 seconds.

·

The airbag ECU assembly detects a short to B+ in the side collision sensor RH circuit (bus 2) for 2 seconds.

·

The airbag ECU assembly detects an open in the side collision sensor RH circuit (bus 2) for 2 seconds.

·

A floor side airbag sensor RH malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Floor side airbag sensor RH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C456406E14
5.51,2.927 6.99,3.354 1.479,0.427 10 false Airbag ECU Assembly 5.5,2.76 5.958,2.927 0.458,0.167 10 false Q1 5.292,0.792 5.75,1.094 0.458,0.302 10 false 28 5.302,1.99 6.052,2.365 0.75,0.375 10 false 29 5.615,0.875 6.073,1.177 0.458,0.302 10 false BCR+ 5.604,2.063 6.354,2.438 0.75,0.375 10 false BCR- 1.729,0.802 2.188,1.104 0.458,0.302 10 false 2 1.729,1.948 2.188,2.25 0.458,0.302 10 false 1 1.229,0.906 1.729,1.208 0.5,0.302 10 false BBR+ 1.198,2.094 1.625,2.302 0.427,0.208 10 false BBR- 0.177,2.781 0.708,2.958 0.531,0.177 10 false Q3 0.198,2.969 2.75,3.177 2.552,0.208 10 false Floor Side Airbag Sensor RH

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Procedure1

c.

Check that the connectors are properly connected to the airbag ECU assembly and side airbag sensor RH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
C208245C43
0.646,1.75 0.958,1.948 0.313,0.198 10 false *1 2.573,1.542 2.885,1.74 0.313,0.198 10 false *2 1.51,0.958 1.823,1.156 0.313,0.198 10 false *3
*1 Floor Side Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the floor side airbag sensor RH connector.


Procedure1

c.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

Pre-procedure1

a.
E466185C02
1.26,3.667 1.677,3.917 0.417,0.25 0.25,0.667 0.667,0.917 0.417,0.25 1.917,4.448 2.167,4.448 2.167,4.448 2.25,4.073 true 2.75,4.448 2.5,4.448 2.5,4.448 2.333,4.073 true 1.167,1.5 1.333,1.5 1.333,1.5 1.49,0.958 true 2,1.5 1.833,1.5 1.833,1.5 1.625,0.948 true 0.385,2.896 0.573,3.063 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.01,2.417 1.198,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.396,2.406 2.583,2.573 0.188,0.167 10 false A 2.844,2.698 3.031,2.865 0.188,0.167 10 false *2 0.385,0.719 0.688,0.875 0.302,0.156 10 false Q3 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.802,1.406 1.313,1.583 0.51,0.177 10 false BBR- 2.063,1.417 2.542,1.583 0.479,0.167 10 false BBR+ 1.552,4.375 1.979,4.573 0.427,0.198 10 false BCR+ 2.781,4.375 3.167,4.531 0.385,0.156 10 false BCR- 1.406,3.708 1.729,3.885 0.323,0.177 10 false Q1 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.594 1.719,2.75 0.229,0.156 10 false *3
*1 Floor Side Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


None


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q3)Location & Routing

Click Connector(Q3)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Floor Side Airbag Sensor RH

Q3-2 (BBR+) - Q3-1 (BBR-) Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E466186C02
1.26,3.667 1.677,3.917 0.417,0.25 0.25,0.75 0.667,1 0.417,0.25 1.542,3.458 1.792,3.458 1.792,3.458 2.24,4.031 true 2.719,3.167 2.469,3.167 2.469,3.167 2.333,4.031 true 1.167,1.5 1.333,1.5 1.333,1.5 1.469,0.958 true 2,1.5 1.833,1.5 1.833,1.5 1.604,0.958 true 1.688,4.417 2.104,4.417 true 0.385,2.896 0.573,3.063 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.01,2.417 1.198,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.396,2.406 2.583,2.573 0.188,0.167 10 false A 2.844,2.698 3.031,2.865 0.188,0.167 10 false *2 0.385,0.802 0.688,0.958 0.302,0.156 10 false Q3 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.802,1.417 1.313,1.594 0.51,0.177 10 false BBR- 2.063,1.417 2.542,1.583 0.479,0.167 10 false BBR+ 1.188,3.385 1.625,3.573 0.438,0.188 10 false BCR+ 2.76,3.083 3.146,3.24 0.385,0.156 10 false BCR- 1.396,3.719 1.719,3.896 0.323,0.177 10 false Q1 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.594 1.719,2.75 0.229,0.156 10 false *3 1.469,4.344 1.906,4.531 0.438,0.188 10 false *4
*1 Floor Side Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Using a service wire, connect terminals 28 (BCR+) and 29 (BCR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q3)Location & Routing

Click Connector(Q3)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Floor Side Airbag Sensor RH

Q3-2 (BBR+) - Q3-1 (BBR-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

Disconnect the service wire from connector B.



OK

5.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

Pre-procedure1

a.
E466185C02
1.26,3.667 1.677,3.917 0.417,0.25 0.25,0.667 0.667,0.917 0.417,0.25 1.917,4.448 2.167,4.448 2.167,4.448 2.25,4.073 true 2.75,4.448 2.5,4.448 2.5,4.448 2.333,4.073 true 1.167,1.5 1.333,1.5 1.333,1.5 1.49,0.958 true 2,1.5 1.833,1.5 1.833,1.5 1.625,0.948 true 0.385,2.896 0.573,3.063 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.01,2.417 1.198,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.396,2.406 2.583,2.573 0.188,0.167 10 false A 2.844,2.698 3.031,2.865 0.188,0.167 10 false *2 0.385,0.719 0.688,0.875 0.302,0.156 10 false Q3 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.802,1.406 1.313,1.583 0.51,0.177 10 false BBR- 2.063,1.417 2.542,1.583 0.479,0.167 10 false BBR+ 1.552,4.375 1.979,4.573 0.427,0.198 10 false BCR+ 2.781,4.375 3.167,4.531 0.385,0.156 10 false BCR- 1.406,3.708 1.729,3.885 0.323,0.177 10 false Q1 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.594 1.719,2.75 0.229,0.156 10 false *3
*1 Floor Side Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


None


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q3)Location & Routing

Click Connector(Q3)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Floor Side Airbag Sensor RH

Q3-2 (BBR+) - Body ground Always 1 MΩ or higher
Q3-1 (BBR-) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK WIRE HARNESS (CHECK FOR SHORT TO +B IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

a.
E466185C02
1.26,3.667 1.677,3.917 0.417,0.25 0.25,0.667 0.667,0.917 0.417,0.25 1.917,4.448 2.167,4.448 2.167,4.448 2.25,4.073 true 2.75,4.448 2.5,4.448 2.5,4.448 2.333,4.073 true 1.167,1.5 1.333,1.5 1.333,1.5 1.49,0.958 true 2,1.5 1.833,1.5 1.833,1.5 1.625,0.948 true 0.385,2.896 0.573,3.063 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.01,2.417 1.198,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.396,2.406 2.583,2.573 0.188,0.167 10 false A 2.844,2.698 3.031,2.865 0.188,0.167 10 false *2 0.385,0.719 0.688,0.875 0.302,0.156 10 false Q3 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.802,1.406 1.313,1.583 0.51,0.177 10 false BBR- 2.063,1.417 2.542,1.583 0.479,0.167 10 false BBR+ 1.552,4.375 1.979,4.573 0.427,0.198 10 false BCR+ 2.781,4.375 3.167,4.531 0.385,0.156 10 false BCR- 1.406,3.708 1.729,3.885 0.323,0.177 10 false Q1 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.594 1.719,2.75 0.229,0.156 10 false *3
*1 Floor Side Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q3)Location & Routing

Click Connector(Q3)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Floor Side Airbag Sensor RH

Q3-2 (BBR+) - Body ground Ignition switch ON Below 1 V
Q3-1 (BBR-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.



OK

7.CHECK FLOOR SIDE AIRBAG SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FLOOR SIDE AIRBAG SENSOR RH
a.
C374693C27
0.979,1.552 1.292,1.708 0.313,0.156 10 false *1 2.458,1.417 2.771,1.573 0.313,0.156 10 false *2 1.646,1.354 1.958,1.51 0.313,0.156 10 false *3
*1 Floor Side Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the connector to the airbag ECU assembly.


b.

Interchange the floor side airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK FLOOR SIDE AIRBAG SENSOR RH
8.CHECK FLOOR SIDE AIRBAG SENSOR RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009787 is output A
DTC B009287 is not output B
DTC B009287 and B009787 are not output C



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Return the floor side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C