Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009E64  Right Side Restraints Sensor 5 Signal Plausibility Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009E64 Right Side Restraints Sensor 5 Signal Plausibility Failure Either condition is met:
·

A side airbag pressure sensor RH malfunction.

·

An airbag ECU assembly malfunction.


·

Side airbag pressure sensor RH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C450171E31
1.594,0.677 1.75,0.875 0.156,0.198 10 false 2 1.583,1.479 1.74,1.677 0.156,0.198 10 false 1 2.854,0.656 3.01,0.854 0.156,0.198 10 false 1 2.844,1.479 3,1.677 0.156,0.198 10 false 2 4.146,0.667 4.302,0.865 0.156,0.198 10 false 4 5.333,0.656 5.646,0.854 0.313,0.198 10 false 26 5.365,1.479 5.677,1.677 0.313,0.198 10 false 25 4.177,1.49 4.333,1.688 0.156,0.198 10 false 3 5.635,0.792 6.25,0.99 0.615,0.198 10 false BBR+ 5.635,1.573 6.25,1.771 0.615,0.198 10 false BBR- 0.094,2.219 0.406,2.417 0.313,0.198 10 false M15 0.094,2.365 2.229,2.583 2.135,0.219 10 false Side Airbag Pressure Sensor RH 2.385,2.208 2.698,2.406 0.313,0.198 10 false Q2 2.385,2.375 5.25,2.698 2.865,0.323 10 false No. 2 Side Airbag Sensor Assembly RH 5.385,2.208 6,2.406 0.615,0.198 10 false Q1 5.385,2.365 6.854,2.677 1.469,0.313 10 false Airbag ECU Assembly 3.073,0.781 3.688,0.979 0.615,0.198 10 false BDR+ 3.083,1.573 3.698,1.771 0.615,0.198 10 false BDR- 3.615,0.781 4.229,0.979 0.615,0.198 10 false BCR+ 3.646,1.583 4.26,1.781 0.615,0.198 10 false BCR- 1.094,0.781 1.708,0.979 0.615,0.198 10 false BDR+ 1.083,1.604 1.698,1.802 0.615,0.198 10 false BDR-

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK SIDE AIRBAG PRESSURE SENSOR RH
a.
B529883C12
0.969,1.521 1.24,1.719 0.271,0.198 10 false *1 2.323,1.531 2.594,1.729 0.271,0.198 10 false *2 1.646,1.271 1.917,1.469 0.271,0.198 10 false *3
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Wire Harness


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


c.

Interchange the side airbag pressure sensor RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

2.CHECK SIDE AIRBAG PRESSURE SENSOR RH
2.CHECK SIDE AIRBAG PRESSURE SENSOR RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B009E64 is output A
DTC B009B64 is output B
DTC B009B64 and B009E64 are not output C


HINT:

Codes other than DTCs B009B64 and B009E64 may be output at this time, but they are not related to this check.



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors.



A

B

C