| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B166A62 | Right Side Restraints Sensor 5 / Left Side Restraints Sensor 5 Signal Compare Failure | The difference between the pressure detected by the side airbag pressure sensor LH and the side airbag pressure sensor RH exceeds a certain value a certain number of times |
·
Side airbag pressure sensor LH
·
Side airbag pressure sensor RH
·
Airbag ECU assembly |
Comes on | SRS Airbag | B | Not applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Pre-procedure1
None
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B009B00, B009B09, B009B64, B009B83, B009B84, B009B85, B009B87, B009B96, B009E00, B009E09, B009E64, B009E83, B009E84, B009E85, B009E87 or B009E96 is output | A |
| DTC B009B00, B009B09, B009B64, B009B83, B009B84, B009B85, B009B87, B009B96, B009E00, B009E09, B009E64, B009E83, B009E84, B009E85, B009E87 or B009E96 is not output | B |
Post-procedure1
None
A
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Replace the side airbag pressure sensor LH with a new one or known good one.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
When using a new part, since the side airbag pressure sensor RH and LH have the same part number, prepare either one.
Use the prepared door side airbag sensor to check the side airbag pressure sensor RH as well.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B166A62 is output | A |
| DTC B166A62 is not output | B |
Codes other than DTC B166A62 may be output at this time, but they are not related to this check.
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Return the left side restraints sensor that was installed for testing to its original location.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
Replace the side airbag pressure sensor RH with a new one or known good one.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
When using a new part, since the side airbag pressure sensor LH and RH have the same part number, prepare either one.
Use the prepared side airbag pressure sensor to check the side airbag pressure sensor LH as well.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B166A62 is output | A |
| DTC B166A62 is not output | B |
Codes other than DTC B166A62 may be output at this time, but they are not related to this check.
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.
Return the right side restraints sensor that was installed for testing to its original location.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL