Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light does not Come ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag ECU assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the airbag ECU assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag ECU assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

B612295E04
5.625,3.75 7.115,4.156 1.49,0.406 10 false Airbag ECU Assembly 2.906,3.76 4.802,4.042 1.896,0.281 10 false Combination Meter Assembly 2.125,2.177 2.99,2.396 0.865,0.219 10 false METER-IGR 0.073,2.021 1.49,2.229 1.417,0.208 10 false from IGR-NO.1 Relay*2 0.792,4.302 3.563,4.531 2.771,0.229 10 false : CAN Communication Line 4.896,0.615 5.781,0.854 0.885,0.24 10 false A/BAG-IGR 2.896,3.573 3.281,3.76 0.385,0.188 10 false I5 3.469,2.042 3.854,2.229 0.385,0.188 10 false IG+ 6.083,0.448 6.469,0.635 0.385,0.188 10 false IGR 3.24,1.885 3.542,2.073 0.302,0.188 10 false 6 3.25,2.76 3.552,2.948 0.302,0.188 10 false 2 5.792,2.75 6.094,2.938 0.302,0.188 10 false 32 5.792,2.24 6.094,2.427 0.302,0.188 10 false 33 5.771,0.344 6.073,0.531 0.302,0.188 10 false 36 6.083,2.375 6.385,2.563 0.302,0.188 10 false E1 6.073,2.896 6.375,3.083 0.302,0.188 10 false E2 3.479,2.885 3.781,3.073 0.302,0.188 10 false ET 5.635,3.573 6.042,3.76 0.406,0.188 10 false I24 2.844,0.427 4.354,0.677 1.51,0.25 10 false from IGR-NO.1 Relay 0.073,1.125 1.5,1.667 1.427,0.542 10 false from Engine Stop and Start ECU*1 0.135,3.177 2.031,3.458 1.896,0.281 10 false *1: w/ Stop and Start System 0.146,3.667 2.042,3.948 1.896,0.281 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the , refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK BATTERY
a.

Measure the battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR

NG

REPLACE OR RECHARGE BATTERY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


c.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTOR
a.
C414925C01
0.74,1.51 1.052,1.708 0.313,0.198 10 false *1 2.677,1.625 2.99,1.823 0.313,0.198 10 false *2 1.698,0.823 2.01,1.021 0.313,0.198 10 false *3
*1 Combination Meter
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the combination meter assembly connector.


b.

Check that the connectors (on the combination meter side) are not damaged.

OK:

The connectors are not deformed or damaged



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Stop and Start System
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-6 (IG+) - Body ground Ignition switch ON 10.5 to 16 V

w/o Stop and Start System
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-6 (IG+) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-2 (ET) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (w/ Stop and Start System) B
NG (w/o Stop and Start System) C



A

5.CHECK SRS WARNING LIGHT

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK SRS WARNING LIGHT
a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Connect the I5 combination meter assembly connector.


c.

Disconnect the I24 airbag ECU assembly connector.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Approximately 6 seconds after the ignition switch is turned to ON, check the condition of the SRS warning light.


Result:
Result Proceed to
Turns off for 10 seconds, and then illuminates A
Turns off for 10 seconds, and then remains off B



A

B

REPLACE COMBINATION METER ASSEMBLY