Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00131A  Passenger Knee Bolster Deployment Control Circuit Resistance Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B00131A Passenger Knee Bolster Deployment Control Circuit Resistance Below Threshold One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal in the front passenger side knee squib circuit for 2 seconds during the primary check.

·

A lower No. 2 instrument panel airbag assembly malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Lower No. 2 instrument panel airbag assembly

·

Airbag ECU assembly


Comes on SRS Airbag A Applicable

WIRING DIAGRAM

E507150E04
0.49,1.698 0.948,1.896 0.458,0.198 10 false I28 0.49,1.875 2.375,2.25 1.885,0.375 10 false Lower No. 2 Instrument Panel Airbag Assembly 1.302,1.115 1.615,1.313 0.313,0.198 10 false PK- 1.323,0.333 1.646,0.531 0.323,0.198 10 false PK+ 1.698,0.313 1.844,0.49 0.146,0.177 10 false 1 1.688,1.115 1.833,1.292 0.146,0.177 10 false 2 5.302,0.344 5.51,0.521 0.208,0.177 10 false 10 5.313,1.115 5.5,1.292 0.188,0.177 10 false 11 5.594,0.448 5.958,0.646 0.365,0.198 10 false PK+ 5.594,1.229 5.958,1.427 0.365,0.198 10 false PK- 5.417,1.708 5.875,1.906 0.458,0.198 10 false I24 5.417,1.865 6.906,2.354 1.49,0.49 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B00131A is output A
Past DTC B00131A is output B



Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Procedure1

c.

Check that the connectors are properly connected to the lower No. 2 instrument panel airbag assembly and airbag ECU assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C208251C26
0.688,0.781 1,0.938 0.313,0.156 10 false *1 2.146,1.646 2.458,1.875 0.313,0.229 10 false *2 1.229,0.781 1.542,0.938 0.313,0.156 10 false *3
*1 Lower No. 2 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the lower No. 2 instrument panel airbag assembly connector.


Procedure1

c.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



d.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



e.

Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

f.

None



OK

4.CHECK LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
a.
C415634C12
0.646,2.135 1.156,2.396 0.51,0.26 2.417,2.469 2.24,2.469 2.24,2.469 2.063,2.292 true 0.958,0.865 1.271,1.021 0.313,0.156 10 false *1 2.49,1.188 2.802,1.344 0.313,0.156 10 false *2 2.469,2.385 2.781,2.542 0.313,0.156 10 false *4 0.646,1.51 0.958,1.667 0.313,0.156 10 false *a 0.771,2.198 1.063,2.354 0.292,0.156 10 false I28 2.01,0.635 2.323,0.792 0.313,0.156 10 false A 1.854,0.646 2.167,0.802 0.313,0.156 10 false B 1.427,0.646 1.74,0.802 0.313,0.156 10 false C 1.125,0.646 1.438,0.802 0.313,0.156 10 false D 1.594,0.854 1.906,1.01 0.313,0.156 10 false *3
*1 Lower No. 2 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*3 Wire Harness
*4 SST
*a Front view of wire harness connector
(to Lower No. 2 Instrument Panel Airbag Assembly)


Connect the I24 airbag ECU assembly connector.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the lower No. 2 instrument panel airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
5.CHECK LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B00131A is not output A
DTC B00131A is output B



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Disconnect SST from connector C.



A

B

6.CHECK HARNESS AND CONNECTOR
6.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
C415635C08
0.646,2 1.052,2.26 0.406,0.26 0.979,2.469 1.094,2.469 1.094,2.469 1.469,2.073 true 2.24,2.458 2.083,2.458 2.083,2.458 1.698,2.073 true 0.823,0.438 1.135,0.594 0.313,0.156 10 false *1 2.375,1.208 2.688,1.365 0.313,0.156 10 false *2 1.5,0.448 1.813,0.604 0.313,0.156 10 false *3 0.573,1.531 0.885,1.688 0.313,0.156 10 false *a 1,0.646 1.167,0.844 0.167,0.198 10 false D 1.302,0.635 1.448,0.823 0.146,0.188 10 false C 1.729,0.646 1.875,0.833 0.146,0.188 10 false B 2.01,0.635 2.156,0.823 0.146,0.188 10 false A 0.667,2.417 1.135,2.615 0.469,0.198 10 false PK+ 2.281,2.396 2.75,2.594 0.469,0.198 10 false PK- 0.75,2.042 1.094,2.208 0.344,0.167 10 false I28
*1 Lower No. 2 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Lower No. 2 Instrument Panel Airbag Assembly)
V100135

Release the activation prevention mechanism


Disconnect the I24 airbag ECU assembly connector.


b.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I28)Location & Routing

Click Connector(I28)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Lower No. 2 Instrument Panel Airbag Assembly

I28-1 (PK+) - I28-2 (PK-) Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

Restore the released activation prevention mechanism of connector B to the original condition.



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.
C238245C39
0.75,1.26 1.313,1.688 0.563,0.427 10 false *1 2.49,1.604 2.823,2.01 0.333,0.406 10 false *2 1.344,0.792 1.906,1.219 0.563,0.427 10 false *3
*1 Lower No. 2 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the lower No. 2 instrument panel airbag assembly connector.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B00131A is not output A
DTC B00131A is output B



Post-procedure1

d.

None



A

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




B