Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467922 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B003012  Second Row Left Side Airbag Deployment Control Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B003012 Second Row Left Side Airbag Deployment Control Circuit Short to Battery One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit to B+ signal in the rear side squib LH circuit for 0.5 seconds.

·

A rear seat airbag assembly LH malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Rear seat airbag assembly LH

·

Airbag ECU assembly


Comes on SRS Airbag A Applicable

WIRING DIAGRAM

E507150E10
5.365,1.677 5.698,1.865 0.333,0.188 10 false S1 5.26,0.323 5.5,0.542 0.24,0.219 10 false 13 5.604,0.427 6.083,0.615 0.479,0.188 10 false SRL+ 5.302,1.104 5.531,1.292 0.229,0.188 10 false 14 1.729,1.104 1.906,1.271 0.177,0.167 10 false 2 1.708,0.354 1.927,0.583 0.219,0.229 10 false 1 5.604,1.229 6,1.406 0.396,0.177 10 false SRL- 5.365,1.833 6.896,2.292 1.531,0.458 10 false Airbag ECU Assembly 0.156,1.667 0.802,1.844 0.646,0.177 10 false k8 0.167,1.833 2.417,2.073 2.25,0.24 10 false Rear Seat Airbag Assembly LH

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B003012 is output A
Past DTC B003012 is output B



Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Procedure1

c.

Check that the connectors are properly connected to the rear seat airbag assembly LH and airbag ECU assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C208249C46
0.74,0.938 1.052,1.135 0.313,0.198 10 false *1 1.24,0.948 1.552,1.146 0.313,0.198 10 false *3 2.208,1.667 2.521,1.865 0.313,0.198 10 false *2
*1 Rear Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the rear seat airbag assembly LH connector.


Procedure1

c.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



d.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



e.

Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

f.

None



OK

4.CHECK REAR SEAT AIRBAG ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR SEAT AIRBAG ASSEMBLY LH
a.
C295801C64
0.438,2.167 0.854,2.417 0.417,0.25 2.177,2.448 2.354,2.594 2.354,2.594 2.521,2.594 true 0.594,0.635 0.917,0.906 0.323,0.271 10 false *1 2.51,1.385 2.885,1.708 0.375,0.323 10 false *2 0.333,1.615 0.667,2.031 0.333,0.417 10 false *a 2.563,2.531 2.802,2.698 0.24,0.167 10 false *4 0.573,2.208 0.938,2.396 0.365,0.188 10 false k8 2.021,0.406 2.396,0.729 0.375,0.323 10 false A 1.854,0.406 2.229,0.729 0.375,0.323 10 false B 1.104,0.406 1.479,0.729 0.375,0.323 10 false C 0.729,0.406 1.104,0.729 0.375,0.323 10 false D 1.417,0.625 1.74,0.896 0.323,0.271 10 false *3
*1 Rear Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 SST
*a Front view of wire harness connector
(to Rear Seat Airbag Assembly LH)


Connect the S1 airbag ECU assembly connector.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the rear seat airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK REAR SEAT AIRBAG ASSEMBLY LH
5.CHECK REAR SEAT AIRBAG ASSEMBLY LH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B003012 is not output A
DTC B003012 is output B



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Disconnect SST from connector C.



A

B

6.CHECK HARNESS AND CONNECTOR
6.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
E449150C04
0.958,2.354 1.375,2.604 0.417,0.25 0.781,0.563 0.938,0.76 0.156,0.198 10 false D 0.708,0.792 1.021,0.948 0.313,0.156 10 false *1 2.365,1.406 2.677,1.563 0.313,0.156 10 false *2 1.313,0.781 1.625,0.938 0.313,0.156 10 false *3 0.344,1.74 0.656,1.896 0.313,0.156 10 false *a 1.073,2.385 1.469,2.583 0.396,0.198 10 false k8 1.99,0.563 2.146,0.76 0.156,0.198 10 false A 1.583,0.563 1.74,0.76 0.156,0.198 10 false B 1.094,0.563 1.25,0.76 0.156,0.198 10 false C
*1 Rear Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Rear Seat Airbag Assembly LH)


Disconnect the S1 airbag ECU assembly connector.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(k8)Location & Routing

Click Connector(k8)Seat>Rear Seat Wire LH>Rear Seat Airbag Assembly LH

k8-1 - Body ground Ignition switch ON Below 1 V
k8-2 - Body ground Ignition switch ON Below 1 V



Post-procedure1

e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 60 seconds.


Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.
C400948C11
0.781,0.927 1.094,1.083 0.313,0.156 10 false *1 2.177,1.604 2.49,1.76 0.313,0.156 10 false *2 1.302,0.938 1.615,1.094 0.313,0.156 10 false *3
*1 Rear Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the rear seat airbag assembly LH connector.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTC B003012 is not output A
DTC B003012 is output B



Post-procedure1None

d.

None



A

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




B