Home › Vehicle Interior › HEATING / AIR CONDITIONING › BLOWER UNIT
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467934 BLOWER UNIT A

HEATING / AIR CONDITIONING  BLOWER UNIT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E464430N01
0.333,0.333 6.833,5.583 6.5,5.25 0.75,0.656 6.167,2.667 5.417,2.01 0.75,3.333 6.167,5.344 5.417,2.01 0.333,2.906 6.833,2.906 false 6.167,1.75 6.5,1.75 false 6.167,4.417 6.5,4.417 false 4.219,4.125 4.552,4.125 false 4.24,1.406 4.573,1.406 false 6.5,1.594 6.781,1.948 0.281,0.354 18 false 1 6.521,4.26 6.802,4.615 0.281,0.354 18 false 1 0.396,0.375 0.771,0.615 0.375,0.24 12 false *A 0.427,2.99 0.802,3.229 0.375,0.24 12 false *B 4.063,1.24 4.344,1.594 0.281,0.354 18 false 2 4.063,3.958 4.344,4.313 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 AIR CONDITIONER UNIT ASSEMBLY - - - -
2 BLOWER ASSEMBLY 87130D - - -

*A for 1-tier Type *B for 2-tier Type

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during blower assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Steering sensor (Including removal and installation) Steering angle neutral point Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Steering angle setting Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
No. 1 blower damper servo sub-assembly Initialization servo motor DTCs are output (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 87130D 2.REMOVE BLOWER ASSEMBLY

a.

for 1-tier Type:

E464432


b.

for 2-tier Type:

E464431C01
0,0 0,0 false
V113147

Remove in this Direction - -