| *A | for 1GR-FE | *B | for V35A-FTS |
| *1 | ENGINE SIDE COVER SUB-ASSEMBLY LH | *2 | ENGINE SIDE COVER SUB-ASSEMBLY RH |
| *A | for V35A-FTS | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 17 | FRONT SEAT ASSEMBLY LH | - | - | - | - |
| 18 | FRONT SEAT ASSEMBLY RH | - | - | - | - |
| *A | w/ Headup Display | - | - |
| *A | w/ Telematics Transceiver | *B | w/ Door Control Battery |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 45 | NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY | 55306A | - | - | - |
| 46 | NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY | 55307C | - | - | - |
| 47 | NO. 1 AIR DUCT SUB-ASSEMBLY | 87201 | - | - | - |
| 48 | HEATER BLOWER WIRE | 82213E | - | - | - |
| 49 | INSTRUMENT PANEL WIRE | 82141 | - | - | - |
| *A | w/ PTC Heater | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 50 | INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY | - | ( ) |
- | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 51 | COOLER UNIT DRAIN HOSE GROMMET | 88539G | ( ) |
- | - |
| 52 | AIR CONDITIONER UNIT ASSEMBLY | - | - | - | - |
| 53 | NO. 1 COOLING UNIT BRACKET | 88536 | - | - | - |
| 54 | NO. 2 COOLING UNIT BRACKET | 88536A | - | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the air conditioner unit assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
When removing the air conditioning radiator damper servo sub-assembly, reinstallation is easier to perform if the following conditions are set before disconnecting the negative (-) battery terminal.
| Item | Condition |
|---|---|
| Air vent damper position | Face |
| Set temperature | Max cool |
11209 1.REMOVE V-BANK COVER SUB-ASSEMBLY (for V35A-FTS)
53292A 2.REMOVE UPPER RADIATOR SUPPORT SEAL
for Standard:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Standard)>REMOVAL
for Aero Type:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Aero Type)>REMOVAL
3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
51410 4.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (LUBRICATION)>OIL LEVEL SENSOR>REMOVAL
for V35A-FIS:
Click hereEngine / Hybrid System>V35A-FTS (LUBRICATION)>OIL PAN AND OIL LEVEL SENSOR>REMOVAL
51420 5.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (for 1GR-FE)
6.DRAIN ENGINE COOLANT
for 1GR-FE:
for V35A-FIS:
7.REMOVE FRONT WIPER MOTOR AND LINK
87237 8.REMOVE HEATER PIPING COVER (for V35A-FTS)
51470C 9.DISCONNECT REAR ENGINE SIDE UNDER COVER ASSEMBLY LH (for V35A-FTS)
|
Disconnect in this Direction | - | - |
55223A 10.DISCONNECT OUTER DASH PANEL INSULATOR
for 1GR-FE:
| *a | LH Side | *b | RH Side |
|
Disconnect in this Direction | - | - |
for V35A-FTS:
| *a | LH Side | *b | RH Side |
|
Disconnect in this Direction | - | - |
11.DISCONNECT OUTLET HEATER WATER HOSE A
for 1GR-FE:
Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose A.
Do not apply excessive force to the outlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
for V35A-FTS:
Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose A.
Do not apply excessive force to the outlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
12.DISCONNECT INLET HEATER WATER HOSE A
for 1GR-FE:
Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.
Do not apply excessive force to the inlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
for V35A-FTS:
Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.
Do not apply excessive force to the inlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
87128 13.REMOVE HEATER GROMMET
88710K 14.DISCONNECT NO. 3 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
|
Rotate in this Direction | - | - |
Remove the bolt.
Rotate the 1-point tightening plate and disconnect the No. 3 air conditioning tube and accessory assembly.
Remove the 2 O-rings from the No. 3 air conditioning tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88897K 15.REMOVE COOLER PIPE GROMMET
16.REMOVE HOLE PLUG
17.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
18.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure described for the LH side.
19.REMOVE INSTRUMENT PANEL SAFETY PAD
55990B 20.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY
45250 22.REMOVE STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
for Power Tilt and Power Telescopic Steering Column:
73233 23.REMOVE OUTER LAP BELT ANCHOR COVER
73220 24.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73210 25.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
Use the same procedure described for the LH side.
67918D 26.REMOVE REAR DOOR SCUFF PLATE LH
62414A 27.REMOVE CENTER PILLAR LOWER GARNISH LH
67917C 28.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
62413A 29.REMOVE CENTER PILLAR LOWER GARNISH RH
Use the same procedure described for the LH side.
78110K 30.REMOVE ACCELERATOR PEDAL(WITH SENSOR) ROD ASSEMBLY
88650N 31.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
58510D 32.REMOVE FRONT FLOOR CARPET ASSEMBLY
|
Pull Out |
|
Fold Up |
|
Fastener | - | - |
|
Pull Out |
|
Fold Up |
|
Fastener | - | - |
55084E 33.REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY
34.REMOVE TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (w/ Telematics Transceiver)
88576C 35.REMOVE NO. 1 COOLER AIR DUCT
|
Remove in this Direction | - | - |
87212K 36.REMOVE REAR NO. 6 AIR DUCT
|
Remove in this Direction | - | - |
87212H 37.REMOVE REAR NO. 4 AIR DUCT
87212J 38.REMOVE REAR NO. 5 AIR DUCT
|
Remove in this Direction | - | - |
87212G 39.REMOVE REAR NO. 3 AIR DUCT
87212F 40.REMOVE REAR NO. 2 AIR DUCT
87212 41.REMOVE REAR NO. 1 AIR DUCT
85940 43.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY
8598A 44.REMOVE DOOR CONTROL BATTERY (w/ Door Control Battery)
55306A 45.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
| *a | Clamp | *b | Guide |
55307C 46.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
| *a | Clamp | *b | Guide |
87201 47.REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY
82213E 48.REMOVE HEATER BLOWER WIRE (w/ PTC Heater)
82141 49.DISCONNECT INSTRUMENT PANEL WIRE
The illustration is an example, so the details may differ.
| *a | Guide | *b | Clamp |
50.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY
|
|
| *A | for 1GR-FE | *B | for V35A-FTS |
| *a | Guide | *b | Clamp |
|
Remove in this Direction | - | - |
88539G 51.REMOVE COOLER UNIT DRAIN HOSE GROMMET
|
|
| *a | Driver Side | *b | Passenger Side |
52.REMOVE AIR CONDITIONER UNIT ASSEMBLY
88536 53.REMOVE NO. 1 COOLING UNIT BRACKET
Perform this procedure only when replacement of the No. 1 cooling unit bracket is necessary.
88536A 54.REMOVE NO. 2 COOLING UNIT BRACKET
Perform this procedure only when replacement of the No. 2 cooling unit bracket is necessary.
Use the same procedure described for the No. 1 cooling unit bracket.