Home › Vehicle Exterior › WINDOW / GLASS › HEATED WINDSHIELD DEFROSTER SYSTEM
RM38G0E _59 Vehicle Exterior _100806 WINDOW / GLASS _0467994 HEATED WINDSHIELD DEFROSTER SYSTEM J

WINDOW / GLASS  HEATED WINDSHIELD DEFROSTER SYSTEM  Heated Windshield Defroster System does not operate  


DESCRIPTION

When the front window deicer switch on the air conditioning control assembly is operated, heated windshield defroster operation request signal is sent to the air conditioning amplifier assembly via LIN communication line.

When the air conditioning amplifier assembly receives the heated windshield defroster operation request signal, the system turns on the HWD relay (HWD NO.1), HWD relay (HWD NO.2) and front wiper deicer relay (DEICER) and operates the heated windshield defroster system.

WIRING DIAGRAM

E468308E01
1.49,1.052 5.813,1.469 4.323,0.417 10 false Air Conditioning Control Assembly (Front Window Deicer Switch) 2.073,1.792 2.99,1.99 0.917,0.198 10 false DEICER 0.76,1.625 1.688,1.854 0.927,0.229 10 false from Battery 2.573,2.458 4.146,2.844 1.573,0.385 10 false Front Wiper Deicer Relay (DEICER) 6.031,2.104 6.646,2.302 0.615,0.198 10 false FDEF 5.542,2.594 7.104,2.99 1.563,0.396 10 false Air Conditioning Amplifier Assembly 0.573,8.51 2.333,8.74 1.76,0.229 10 false : LIN Communication Line 3.198,5.5 4.042,5.885 0.844,0.385 10 false HWD Relay (HWD NO.1) 3.229,7.375 4.042,7.833 0.813,0.458 10 false HWD Relay (HWD NO.2) 4.406,5.167 5.635,5.365 1.229,0.198 10 false HWD NO.1 4.406,7.083 5.635,7.281 1.229,0.198 10 false HWD NO.2 5.646,5 7.135,5.292 1.49,0.292 10 false from Battery 0.333,7.938 1.458,8.156 1.125,0.219 10 false Windshield Glass 3.844,1.531 4,1.729 0.156,0.198 10 false 3 2.76,1.51 2.948,1.729 0.188,0.219 10 false 5 3.854,1.969 4.01,2.167 0.156,0.198 10 false 1 2.75,1.948 2.948,2.177 0.198,0.229 10 false 2 3.052,4.375 3.208,4.573 0.156,0.198 10 false 2 3.052,7.01 3.208,7.208 0.156,0.198 10 false 4 3.042,4.885 3.198,5.083 0.156,0.198 10 false 3 3.052,6.26 3.208,6.458 0.156,0.198 10 false 2 4.104,4.875 4.26,5.073 0.156,0.198 10 false 5 4.083,6.792 4.24,6.99 0.156,0.198 10 false 5 4.083,4.396 4.24,4.594 0.156,0.198 10 false 1 4.094,6.26 4.25,6.458 0.156,0.198 10 false 1 5.542,2.417 6,2.615 0.458,0.198 10 false I33 5.74,1.969 6.052,2.167 0.313,0.198 10 false 22 1.76,6.375 2.375,6.573 0.615,0.198 10 false B26 1.844,4.76 2,4.958 0.156,0.198 10 false 1 1.823,4.271 1.979,4.469 0.156,0.198 10 false 2 1.833,6.094 1.99,6.292 0.156,0.198 10 false 1 1.823,6.656 1.979,6.854 0.156,0.198 10 false 2 0.188,7.135 1.375,7.521 1.188,0.385 10 false Heated Windshield Defroster 1.76,4.51 2.219,4.708 0.458,0.198 10 false B25 1.76,5.01 2.219,5.208 0.458,0.198 10 false B25 1.74,6.896 2.354,7.094 0.615,0.198 10 false B26 5.656,6.896 6.875,7.156 1.219,0.26 10 false from Battery 1.896,2.24 2.938,2.427 1.042,0.188 10 false ENG-IGR NO.2 0.198,2.073 1.615,2.344 1.417,0.271 10 false from IGR NO.3 Relay 0.219,3.594 1.406,3.979 1.188,0.385 10 false Windshield Deicer 3.042,6.781 3.198,6.979 0.156,0.198 10 false 3 3.052,5.115 3.208,5.313 0.156,0.198 10 false 4 1.76,3.354 2.219,3.552 0.458,0.198 10 false B26 1.74,2.844 2.198,3.042 0.458,0.198 10 false B26 1.833,3.115 1.99,3.313 0.156,0.198 10 false 3 1.854,2.615 2.01,2.813 0.156,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the ambient temperature is 5°C (41°F) or higher, or if a malfunction of the ambient temperature sensor (thermistor assembly) is detected, the HWD NO.1, HWD NO.2 or DECIER relays will be deactivated and the front window deicer switch indicator light will blink.



PROCEDURE

1.CHECK AIR CONDITIONING SYSTEM
a.

Check the air conditioning system.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:

Both the heated windshield defroster system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.


OK:

The air conditioning system operates normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Deicer Relay Windshield glass (heated windshield defroster) OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Front Deicer Relay
50004 450 8
OK:

The heated windshield defroster system operates normally.



Result:
Result Proceed to
OK A
NG (Neither windshield glass [heated windshield defroster] LH side nor windshield glass [heated windshield defroster] RH side does not warm up.) B
NG (Only windshield glass [heated windshield defroster] LH side does not warm up.) C
NG (Only windshield glass [heated windshield defroster] RH side does not warm up.) D



A

3.CHECK AIR CONDITIONING CONTROL ASSEMBLY (FRONT WINDOW DEICER SWITCH)

B

4.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.1] - BODY GROUND)

C

5.INSPECT HWD RELAY (HWD NO.2)

D

9.INSPECT HWD RELAY (HWD NO.1)
3.CHECK AIR CONDITIONING CONTROL ASSEMBLY (FRONT WINDOW DEICER SWITCH)
a.

Replace the air conditioning control assembly with a new or known good one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL


b.

Check that the heated windshield defroster system operates normally.

OK:

The heated windshield defroster system operates normally.



Result:
Proceed to
OK
NG



OK

END (AIR CONDITIONING CONTROL ASSEMBLY [FRONT WINDOW DEICER SWITCH] IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.1] - BODY GROUND)
a.

Remove the HWD relay (HWD NO.1) and HWD relay (HWD NO.2) from the No. 2 engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.1) relay holder terminal-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HWD RELAY (HWD NO.2)

OK

6.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.2] - BATTERY AND BODY GROUND)

NG

REPLACE HWD RELAY (HWD NO.2)

6.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.2] - BATTERY AND BODY GROUND)
a.

Remove the HWD relay (HWD NO.1) and HWD relay (HWD NO.2) from the No. 1 engine room relay block assembly.


b.
E409126C01
0.083,0.042 0.396,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to HWD Relay [HWD NO.2])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.2) holder terminal-5 - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.2) holder terminal-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FRONT WIPER DEICER RELAY [DEICER] - HWD RELAY [HWD NO.2])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (FRONT WIPER DEICER RELAY [DEICER] - HWD RELAY [HWD NO.2])
a.

Remove the front wiper deicer relay (DEICER), HWD relay (HWD NO.1) and HWD relay (HWD NO.2) from the No. 1 engine room relay block assembly.


b.

Disconnect the B26 windshield glass (heated windshield defroster) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Front wiper deicer relay (DEICER) holder terminal-3 - HWD relay (HWD NO.2) holder terminal-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] - HWD RELAY [HWD NO.2] AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] - HWD RELAY [HWD NO.2] AND BODY GROUND)
a.

Disconnect the B25 and B26 windshield glass (heated windshield defroster) connectors.


b.

Remove the HWD relay (HWD NO.2) from the No. 1 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B26)Location & Routing

Click Connector(B26)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Windshield Glass

B26-2 - HWD relay (HWD NO.2) relay holder terminal-3 Always Below 1 Ω
B26-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD GLASS (HEATED WINDSHIELD DEFROSTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT HWD RELAY (HWD NO.1)

OK

10.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.1] - BATTERY AND BODY GROUND)

NG

REPLACE HWD RELAY (HWD NO.1)

10.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.1] - BATTERY AND BODY GROUND)
a.

Remove the HWD relay (HWD NO.1) and HWD relay (HWD NO.2) from the No. 1 engine room relay block assembly.


b.
E409126C01
0.083,0.042 0.396,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to HWD Relay [HWD NO.1])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.1) holder terminal-5 - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.1) holder terminal-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FRONT WIPER DEICER RELAY [DEICER] - HWD RELAY [HWD NO.1])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (FRONT WIPER DEICER RELAY [DEICER] - HWD RELAY [HWD NO.1])
a.

Remove the front wiper deicer relay (DEICER), HWD relay (HWD NO.1) and HWD relay (HWD NO.2) from the No. 1 engine room relay block assembly.


b.

Disconnect the B25 windshield glass (heated windshield defroster) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Front wiper deicer relay (DEICER) holder terminal-3 - HWD relay (HWD NO.1) holder terminal-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] - HWD RELAY [HWD NO.1] AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] - HWD RELAY [HWD NO.1] AND BODY GROUND)
a.

Disconnect the B25 and B26 windshield glass (heated windshield defroster) connectors.


b.

Remove the HWD relay (HWD NO.1) from the No. 1 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B25)Location & Routing

Click Connector(B25)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Windshield Glass

B25-1 - HWD relay (HWD NO.1) relay holder terminal-3 Always Below 1 Ω
B25-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD GLASS (HEATED WINDSHIELD DEFROSTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR