| *A | except 1GR-FE | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 12 | ROOF HEADLINING ASSEMBLY | - | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 13 | FORWARD RECOGNITION CAMERA | 8646C | - | - | - |
| 14 | INNER REAR VIEW MIRROR ASSEMBLY | 87810 | - | - | - |
| 15 | INNER REAR VIEW MIRROR ASSEMBLY | 87810 | - | - | - |
| 16 | RAIN SENSOR | 89941 | - | - | - |
| *A | w/o EC Inner Mirror | *B | w/ EC Inner Mirror |
| *C | w/ Rain Sensor | *D | w/ Front Camera |
| *A | for 1-piece Type | *B | for 2-piece Type |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the windshield glass removal/installation are shown below.
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also the dynamic radar cruise control system, front camera system, lane tracing assist system, lane departure alert system, road sign assist system, pre-collision system, adaptive high beam system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
75533 5.REMOVE WINDSHIELD OUTSIDE MOULDING RH
|
Use the same procedure described for the LH side. |
51473C 6.REMOVE ENGINE SIDE COVER RH (except 1GR-FE)
51474B 7.REMOVE ENGINE SIDE COVER LH (except 1GR-FE)
53383B 8.REMOVE HOOD TO COWL TOP SEAL
55781D 9.REMOVE COWL TOP VENTILATOR LOUVER RH
55782D 10.REMOVE COWL TOP VENTILATOR LOUVER LH
12.REMOVE ROOF HEADLINING ASSEMBLY
8646C 13.REMOVE FORWARD RECOGNITION CAMERA (w/ Front Camera)
87810 14.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
87810 15.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
89941 16.REMOVE RAIN SENSOR (w/ Rain Sensor)
56111 17.REMOVE WINDSHIELD GLASS
|
|
|
Protective Tape | - | - |
Apply protective tape on the body surface around the outer edge of the windshield glass to the left, right and top sides.
When reusing the windshield glass:
| *a | Matchmarks | - | - |
Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.
| *a | Cut | - | - |
Using a utility knife, cut the windshield outside moulding.
Do not damage the windshield glass or body surface.
If the body panel is damaged, perform rust-prevention treatment after removing the windshield glass.
w/ Windshield Deicer:
| *a | w/ Heated Windshield Defroster | - | - |
Detach the clamp and disconnect the 2 connectors.
| *a | Suction Cups | - | - |
Install the suction cups to the windshield glass.
| *1 | No. 1 Windshield Glass Stopper | - | - |
| *a | Piano Wire | - | - |
When using a piano wire, perform the following procedure.
1. Pass the piano wire (0.6 mm is appropriate) and install both ends on the mighty puller as shown in the illustration.
2. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
3. Pull the piano wire back and forth and cut through the adhesive of the windshield glass leaving the windshield glass stopper.
When working near the instrument panel, place a plastic sheet so that the piano wire does not damage the instrument panel.
When working near the curtain shield airbag, be careful not to damage it with the piano wire. (w/ Rear No. 2 Seat, Curtain Shield Airbag)
Do not forcefully allow the piano wire to come to contact with the edges of the windshield glass.
Be careful as the piano wire will break if it crosses itself.
| *A | for 1-piece Type | *B | for 2-piece Type |
| *1 | No. 1 Windshield Glass Stopper | *2 | No. 2 Windshield Glass Stopper |
Holding the suction cups, detach the 2 windshield glass stoppers and remove the windshield glass.
Be careful not to drop the windshield glass.
56115A 18.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)
When reusing the windshield glass:
| *a | Backside | - | - |
Using a scraper, remove the 2 No. 1 windshield glass stoppers.
Do not damage the windshield glass.
Always replace the installed No. 1 windshield glass stopper with a new 2-piece type No. 1 windshield glass stopper.
56116C 19.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
When reusing the windshield glass:
| *a | Backside | - | - |
Using a scraper, remove the 2 No. 2 windshield glass stoppers.
Do not damage the windshield glass.
Always replace the installed No. 2 windshield glass stopper with a new 2-piece type No. 2 windshield glass stopper.
56115A 20.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Remove the 2 No. 1 window glass stoppers from the body.
Always replace the installed No. 1 windshield glass stopper with a new 2-piece type No. 1 windshield glass stopper.
75531D 21.REMOVE WINDSHIELD OUTSIDE UPPER MOULDING
When reusing the windshield glass:
| *a | Backside | - | - |
Using a scraper, remove the windshield outside upper moulding.
Do not damage the windshield glass.
Always replace the installed windshield outside upper moulding with a new windshield outside upper moulding.
55356D 22.REMOVE NO. 2 INSTRUMENT PANEL CUSHION
When reusing the windshield glass:
| *a | Backside | - | - |
Using a scraper, remove the No. 2 instrument panel cushion.
Do not damage the windshield glass.
Always replace the installed No. 2 instrument panel cushion with a new No. 2 instrument panel cushion.
56117A 23.REMOVE WINDOW GLASS ADHESIVE DAM
When reusing the windshield glass:
| *a | Backside | - | - |
Using a scraper, remove the window glass adhesive dam.
Do not damage the windshield glass.
Always replace the installed windshield glass adhesive dam with a new windshield glass adhesive dam.
56119C 24.REMOVE WINDSHIELD GLASS SEAL
|
|
| *a | Backside | - | - |
Using a scraper, remove the windshield glass seal.
Do not damage the windshield glass.