Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY › 2021.04–2022.11
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468040 HEADLIGHT ASSEMBLY A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
E465353N01
4.25,5.406 6.177,6.865 1.927,1.458 5.135,1.073 6.042,1.333 0.906,0.26 3.75,3.031 3.75,2.698 false 3.094,5.646 2.677,5.646 false 5.604,6 5.219,6 false 6.667,4.365 6.5,4.365 6.5,4.365 6.365,4.656 false 6.583,3.531 6.417,3.531 6.417,3.531 6.333,3.792 false 5,4.333 4.667,4.333 false 4.854,0.854 4.604,0.854 4.604,0.854 4.438,1.188 false 6.073,2.302 5.698,2.302 5.698,2.302 5.698,1.885 false 3.99,1.51 3.594,1.51 false 5.26,2.042 5.26,2.406 false 2.938,3.646 2.604,3.646 false 6.365,1.552 6.365,1.208 6.365,1.208 6.052,1.208 false 1.438,2.531 1.438,2.198 false 0.073,0.094 0.448,0.333 0.375,0.24 12 false *A 4.906,0.729 5.375,1.104 0.469,0.375 18 false 9 3.417,3.531 3.885,3.906 0.469,0.375 18 false 7 5.969,5.875 6.438,6.25 0.469,0.375 18 false 5 6.667,3.385 7.135,3.76 0.469,0.375 18 false 4 6.75,4.25 7.031,4.646 0.281,0.396 18 false 3 6.354,2.167 6.729,2.531 0.375,0.365 18 false 2 5.208,2.458 5.75,2.833 0.542,0.375 18 false 1 5.354,4.198 5.823,4.573 0.469,0.375 18 false 6 0.5,5.51 0.958,5.708 0.458,0.198 10 false x 7 4.344,5.479 4.719,5.719 0.375,0.24 12 false *B 6.573,5.219 7.031,5.417 0.458,0.198 10 false x 2 5.854,4.063 6.313,4.26 0.458,0.198 10 false x 2 3.448,5.521 3.917,5.896 0.469,0.375 18 false 8 3.667,3.073 4.125,3.271 0.458,0.198 10 false *1 6.469,1.479 6.927,1.677 0.458,0.198 10 false x 3 3.448,1.438 3.76,1.635 0.313,0.198 10 false *2 5.052,2.49 5.208,2.688 0.156,0.198 10 false ● 5.208,1.135 6.271,1.344 1.063,0.208 8 false 0.8 (8, 7 in.*lbf) 5.042,6.552 5.5,6.75 0.458,0.198 10 false x 2 3.302,3.563 3.458,3.76 0.156,0.198 10 false ● 0.292,2.375 0.75,2.573 0.458,0.198 10 false x 3 1.417,2.563 1.875,2.76 0.458,0.198 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 GASKET 81117B - - -
2 HEADLIGHT LED UNIT ASSEMBLY LH 81160A (Click here) - -
3 HEADLIGHT LEVELING MOTOR LH 85691 - - -
4 HEADLIGHT BRACKET LH 81156A - - -
5 LIGHT CONTROL LED ECU LH 85967D (Click here) - -
6 HEADLIGHT UNIT LH 81171A (Click here) - -
7 HEADLIGHT LENS GASKET 81132B (Click here) - -
8 HEADLIGHT LENS SUB-ASSEMBLY LH 8110B (Click here) - -
9 NO. 1 HEADLIGHT COVER 81144 - - -

*A w/ Headlight ECU *B w/ Sequential Turn Light
*1 Headlight Housing LH *2 Gasket
*3 BASE B ASSEMBLY - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -
● Non-reusable part - -

E468531N01
2.479,3.781 2.979,3.781 false 2.531,5.99 2.896,5.99 true 4.927,4.667 5.167,4.667 true 6.052,1.729 6.052,2.042 6.052,2.042 6.417,2.042 true 5.021,1.552 5.021,0.917 5.021,0.917 5.271,0.917 false 4.427,1.656 4.01,1.656 false 5.677,1.677 5.677,1.042 5.677,1.042 5.927,1.042 false 6.417,3.031 6.417,3.594 false 0.177,0.125 0.552,0.365 0.375,0.24 12 false *A 5.344,0.813 5.625,1.167 0.281,0.354 18 false 9 6.49,1.917 6.875,2.25 0.385,0.333 18 false 3 3.198,3.625 3.594,3.979 0.396,0.354 18 false ●7 5.469,4.542 5.75,4.896 0.281,0.354 18 false 6 3.24,5.885 3.521,6.24 0.281,0.354 18 false 8 5.99,0.927 6.448,1.125 0.458,0.198 10 false ●*1 0.417,5.813 0.875,6.01 0.458,0.198 10 false x 7 3.875,1.573 4.188,1.771 0.313,0.198 10 false *1 6.302,3.688 6.813,4.073 0.51,0.385 18 false 10

Procedure Part Name Code
Z101186

Z101188

Z101187

3 HEADLIGHT LEVELING MOTOR LH 85691 - - -
6 HEADLIGHT UNIT LH 81171A (Click here) - -
7 HEADLIGHT LENS GASKET 81132B (Click here) - -
8 HEADLIGHT LENS SUB-ASSEMBLY LH 8110B (Click here) - -
9 NO. 1 HEADLIGHT COVER 81144 - - -
10 HEADLIGHT CORD LH 81165 - - -

*A w/o Headlight ECU - -
*1 Gasket - -
● Non-reusable part - -

E465328N05
2.885,3.448 5.24,5.427 2.354,1.979 4.167,4.646 4.698,4.646 false 4.073,3.948 4.604,3.948 false 5.25,4.313 5.781,4.313 false 4.75,0.906 5,0.906 false 3.927,5.167 4.385,5.365 0.458,0.198 10 false x 3 4.75,4.573 5.063,4.771 0.313,0.198 10 false *1 5.583,0.792 6.396,1.26 0.813,0.469 18 false 11 4.688,3.854 4.844,4.052 0.156,0.198 10 false ● 5.385,0.823 5.542,1.021 0.156,0.198 10 false ● 4.875,3.823 5.458,4.177 0.583,0.354 18 false 12 5.885,4.188 6.344,4.531 0.458,0.344 18 false 13 2.958,3.51 3.333,3.75 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

11 NO. 1 HEADLIGHT PROTECTOR LH 81176 (Click here) - -
12 HEADLIGHT GASKET 81134 - - -
13 HEADLIGHT ECU SUB-ASSEMBLY LH 81056A - - -

*A w/ Headlight ECU - -
*1 HEADLIGHT ECU LH - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 81117B 1.INSTALL GASKET (w/ Headlight ECU)

Hide 81160A 2.INSTALL HEADLIGHT LED UNIT ASSEMBLY LH (w/ Headlight ECU)

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)

Hide 85691 3.INSTALL HEADLIGHT LEVELING MOTOR LH

Hide 81156A 4.INSTALL HEADLIGHT BRACKET LH

Hide 85967D 5.INSTALL LIGHT CONTROL LED ECU LH (w/ Sequential Turn Light)

Z101186

(Click here)

Hide 81171A 6.INSTALL HEADLIGHT UNIT LH

Z101186

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04020, 09891-04010, 09891-04030, 09891-04040)

a.
E465358C04
0.615,0.104 7.031,1.885 6.417,1.781 0.625,1.979 6.99,3.667 6.365,1.688 1.854,0.76 2.458,0.385 true 5.531,1.01 6.219,0.448 true 2.521,0.25 2.833,0.448 0.313,0.198 10 false *1 6.25,0.292 6.563,0.49 0.313,0.198 10 false *1 0.479,0.333 0.76,0.688 0.281,0.354 18 false i 0.469,2.281 0.75,2.635 0.281,0.354 18 false ii 0.688,0.177 1.063,0.417 0.375,0.24 12 false *A 0.719,2.031 1.094,2.271 0.375,0.24 12 false *A 3.885,0.188 4.26,0.427 0.375,0.24 12 false *B 3.948,2.042 4.323,2.281 0.375,0.24 12 false *B
*A w/ Headlight ECU *B w/o Headlight ECU
*1 Pivot Collar - -
V113147

Install in this Direction
V113148

Turn in this Direction


i.

Attach the pivot collar and temporarily install the headlight unit assembly LH to the headlight housing LH as shown in the illustration.



b.
E465343C01
0.083,0.083 7,1.833 6.917,1.75 0.083,1.917 7,3.667 6.917,1.75 1.792,1.375 2.021,1.552 0.229,0.177 10 true a 5.948,1.313 6.177,1.49 0.229,0.177 10 true b 0.438,0.292 0.719,0.646 0.281,0.354 18 false i 6.125,2.667 6.354,2.844 0.229,0.177 10 true a 0.427,2.24 0.708,2.594 0.281,0.354 18 false i 0.146,0.146 0.521,0.385 0.375,0.24 12 false *A 0.167,2 0.542,2.24 0.375,0.24 12 false *B
*A w/ Headlight ECU *B w/o Headlight ECU


i.

Hold the headlight unit assembly LH with one hand to prevent it from tipping over, alternately tighten the aiming screws for the beam axis horizontal and vertical adjustments in the direction indicated by the arrow shown in the illustration, and align the dimensions with the recorded values at removal.



c.
E465345C02
0.208,0.104 0.583,0.344 0.375,0.24 12 false *A 3.719,0.104 4.094,0.344 0.375,0.24 12 false *B
*A w/ Headlight ECU *B w/o Headlight ECU


i.

Connect the each connector and attach the wire harness clamp.



Hide 81132B 7.INSTALL HEADLIGHT LENS GASKET

Z101186

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04020, 09891-04010, 09891-04030, 09891-04040)

a.
E475305C01
5,1 5.427,0.833 true 4.865,1.677 5.292,1.51 true 3.906,0.688 4.188,1.042 0.281,0.354 18 false ii 6.521,1.51 6.802,1.865 0.281,0.354 18 false iii 0.792,2.417 1.073,2.771 0.281,0.354 18 false iv 0.698,0.729 0.979,1.083 0.281,0.354 18 false i 5.49,0.76 5.802,0.958 0.313,0.198 10 false *b 4.677,1.615 4.99,1.813 0.313,0.198 10 false *a 5.427,1 5.969,1.479 0.542,0.479 10 false (1) 4.313,1.135 4.917,1.563 0.604,0.427 10 false (2)
*a Peeling Paper *b Tape


i.

Clean the headlight lens gasket installation groove.


ii.

Cut the peeling paper and secure with tape to the tip of a screwdriver in the order shown in the illustration.

NOTICE:

Use the peeling paper attached to the new headlight lens gasket.



iii.

Using scissors, cut the end of the headlight lens gasket at a 45° angle.


iv.

Insert the headlight lens gasket into the groove of the headlight assembly LH so that the joint comes to the bottom.



b.
E475306C01
3.354,1.24 3.635,1.594 0.281,0.354 18 false i 1.781,2.021 2.063,2.375 0.281,0.354 18 false ii 4.313,0.271 4.594,0.625 0.281,0.354 18 false iii 1.146,2.104 1.458,2.302 0.313,0.198 10 false *a
*c 10 mm (0.394 in.) +/- 5 mm (0.197 in.) - -


i.

Using a screwdriver with the tip wrapped with peeling paper, push in the headlight lens gasket to the groove bottom of the headlight assembly LH.

NOTICE:
·

Gently set the headlight lens gasket into place without pulling on it.

·

If the headlight lens gasket is set while pulled, the gasket will be lifted up at the corner groove.




ii.

After completely pushing in the headlight lens gasket, install it so that the edge overlaps itself by 10 mm (0.394 in.) +/- 5 mm (0.197 in.) or more.


iii.

Check the installation condition of the headlight lens gasket.

NOTICE:
·

Do not allow the headlight lens gasket to lift up or protrude.

·

Do not allow gaps where the headlight lens gasket overlaps.

·

Check the corner groove carefully since the gasket can easily become





Hide 8110B 8.INSTALL HEADLIGHT LENS SUB-ASSEMBLY LH

Z101186

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04020, 09891-04010, 09891-04030, 09891-04040)

a.
E475408C01
0.771,0.198 1.052,0.552 0.281,0.354 18 false i 0.76,1.865 1.042,2.219 0.281,0.354 18 false ii
V113146

Place Hand Here
V100155

Cleaning Area


i.

Be sure to clean the headlight lens gasket contact surface of the headlight lens sub-assembly LH.


ii.

Attach the claw and install the headlight lens sub-assembly LH.



b.
E474583C02
4.51,1.375 4.823,1.573 0.313,0.198 10 false *a 2.188,0.052 3.563,0.406 1.375,0.354 18 false i, ii 5.031,0.073 5.406,0.313 0.375,0.24 12 false *A
*A w/ Headlight ECU - -
*a "TORX" Screw - -


i.

w/ Headlight ECU:

1.

Install the 7 screws.

2.

Using a T20H "TORX" driver, install the "TORX" screw.



ii.

w/o Headlight ECU:

1.

Install the 6 screws.

2.

Using a T20H "TORX" driver, install the "TORX" screw.




Hide 81144 9.INSTALL NO. 1 HEADLIGHT COVER

Hide 81165 10.INSTALL HEADLIGHT CORD LH (w/o Headlight ECU)

Hide 81176 11.INSTALL NO. 1 HEADLIGHT PROTECTOR LH

a.
E465364C03
2.021,2.719 2.135,2.604 true 5.188,1.99 5.26,1.781 true 5.271,3.219 5.135,3.063 true 4.979,2.906 5.177,3.104 0.198,0.198 10 true *a 5.198,1.604 5.396,1.802 0.198,0.198 10 true *a 2.198,2.479 2.396,2.677 0.198,0.198 10 true *a 2.427,0.375 2.708,0.729 0.281,0.354 18 false i 1.073,1.948 2.104,2.271 1.031,0.323 18 false ii, iii, iv
*a Mark-off line - -
V100155

Cleaning Area - -


i.

Clean the application area shown in the illustration.


ii.

Align with the mark-off line and set the No. 1 headlight protector LH into place.


iii.

Align the No. 1 headlight protector LH with the curve and set only the part where the peeling type tape was removed from into place.


iv.

Press the set portion of the part with your finger to secure it.

NOTICE:

Do not slide your finger horizontally, as doing so may stretch the part unnecessarily.




Hide 81134 12.INSTALL HEADLIGHT GASKET (w/ Headlight ECU)

Hide 81056A 13.INSTALL HEADLIGHT ECU SUB-ASSEMBLY LH (w/ Headlight ECU)