| *A | for Step | - | - |
| *1 | REAR BUMPER COVER | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 22 | REAR NO. 2 STEP COVER | 51776B | - | - | - |
| 23 | REAR BUMPER EXTENSION | 52151G | - | - | - |
| *A | w/o Towing Hitch | *B | w/ Towing Hitch |
| *A | w/ Hands Free Power Back Door | *B | w/ TOYOTA Parking Assist-sensor System |
| ● | Non-reusable part | - | - |
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
57615C 1.INSTALL REAR BUMPER ARM BRACKET
52168B 2.INSTALL REAR BUMPER EXTENSION MOUNTING BRACKET LH
52167B 3.INSTALL REAR BUMPER EXTENSION MOUNTING BRACKET RH
52615 4.INSTALL REAR BUMPER ENERGY ABSORBER
58724B 5.INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR
58723B 6.INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR
52592 7.INSTALL REAR BUMPER SIDE SEAL LH
|
Screw |
|
Clip |
Install the rear bumper side seal LH with the 2 clips.
Using a 4 mm hexagon socket wrench, install the screw.
52591 8.INSTALL REAR BUMPER SIDE SEAL RH
Use the same procedure described for the LH side.
52156A 9.INSTALL REAR BUMPER SIDE SUPPORT LH
52155A 10.INSTALL REAR BUMPER SIDE SUPPORT RH
52563D 11.INSTALL REAR BUMPER UPPER RETAINER LH
52562E 12.INSTALL REAR BUMPER UPPER RETAINER RH
81561D 13.INSTALL REAR COMBINATION LIGHT LENS AND BODY LH
81551D 14.INSTALL REAR COMBINATION LIGHT LENS AND BODY RH
52166A 15.INSTALL REAR BUMPER UPPER COVER LH (for Step)
52165A 16.INSTALL REAR BUMPER UPPER COVER RH (for Step)
52461F 17.INSTALL REAR BUMPER PAD
|
|
| Part | Temperature |
|---|---|
| Rear Bumper Cover | 20 to 30°C (68 to 86°F) |
| Rear Bumper Pad | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper cover and rear bumper pad excessively.
| *a | Mark-off Line | - | - |
|
Installation Area | - | - |
Clean the surface of the rear bumper cover.
1. When reusing the rear bumper cover, remove remaining double-sided tape from the rear bumper cover.
2. Using a heat light, heat the rear bumper cover surface.
3. Remove any remaining double-sided tape from the rear bumper cover.
4. Wipe off any tape adhesive residue with cleaner.
Installing the rear bumper pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean a new rear bumper cover surface.
Using a heat light, heat the rear bumper cover and a new rear bumper pad.
Install the rear bumper pad in the position shown in the illustration.
The application strength of the rear bumper pad will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the rear bumper cover.
Use the same procedure for the other side.
52116F 18.INSTALL REAR BUMPER RETAINER
81920 19.INSTALL REFLEX REFLECTOR ASSEMBLY LH
81910 20.INSTALL REFLEX REFLECTOR ASSEMBLY RH
52169C 21.INSTALL REAR BUMPER LOWER COVER
51776B 22.INSTALL REAR NO. 2 STEP COVER (w/ Towing Hitch)
52151G 23.INSTALL REAR BUMPER EXTENSION
82183A 24.INSTALL REAR BUMPER WIRE (w/ TOYOTA Parking Assist-sensor System)
89C48A 25.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89C48B 26.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89342 27.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89342A 28.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
29.INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)
891B0 30.INSTALL KICK DOOR CONTROL SENSOR ASSEMBLY (w/ Hands Free Power Back Door)