Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WINDSHIELD OUTSIDE MOULDING
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468079 WINDSHIELD OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  WINDSHIELD OUTSIDE MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B609593N01
3.917,0.958 4,0.958 4,0.958 4.083,1.125 false 4.26,1.479 4.51,1.479 false 2.167,1.042 2.333,0.708 2.333,0.708 2.5,0.708 false 5,1.75 5.5,1.75 false 3.719,0.833 4,1.188 0.281,0.354 18 false 1 4.052,1.344 4.333,1.698 0.281,0.354 18 false 2 2.833,0.583 3.115,0.938 0.281,0.354 18 false 3 5.969,1.594 6.25,1.948 0.281,0.354 18 false 4 5.833,1.635 6.115,1.99 0.281,0.354 10 false ● 4.604,1.354 5.063,1.552 0.458,0.198 10 false x 4 4.99,1.792 5.448,1.99 0.458,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WINDSHIELD OUTSIDE MOULDING LH 75534 (Click here) - -
2 NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP 75545B - - -
3 WINDSHIELD GLASS 56111 (Click here) - -
4 NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP 75547B (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 3 windshield outside moulding clip removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Windshield glass (Including removal and installation) Adjust forward recognition camera
·

Dynamic radar cruise control system

·

Front camera system

·

Lane tracing assist system

·

Lane departure alert system

·

Road sign assist system

·

Pre-collision system

·

Adaptive high beam system

·

Automatic high beam system


One Time Recognition:
(Click here)
Sequential Recognition:
(Click here)
Driving Adjustment:
(Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75534 1.REMOVE WINDSHIELD OUTSIDE MOULDING LH

a.
B609592C01
2.823,0.677 3.104,1.031 0.281,0.354 18 false i 2.833,1.74 3.083,2.01 0.25,0.271 18 true ii 4.135,0.563 4.417,0.917 0.281,0.354 18 true iii 2.167,3.563 2.448,3.917 0.281,0.354 18 true iv 5.104,1.583 5.323,1.76 0.219,0.177 10 true (1) 5.188,1.302 5.427,1.479 0.24,0.177 10 true (2) 5.365,0.99 5.604,1.167 0.24,0.177 10 true (3) 5.51,0.667 5.75,0.844 0.24,0.177 10 true (4)
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3)


i.

Put protective tape around the windshield outside moulding LH.


ii.

Using a clip remover with its tip wrapped with protective tape, detach the clip as shown in the illustration.


iii.

Place your hand at the position shown in the illustration and detach the claw in the order shown in the illustration.


iv.

Pull the outside windshield moulding LH toward the front of the vehicle and detach the claw and remove the outside windshield moulding LH.



Hide 75545B 2.REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

a.
B609594


Hide 56111 3.REMOVE WINDSHIELD GLASS

Z101186

HINT:

Perform the following procedure only when replacement of the No. 3 windshield outside moulding clip is necessary.

Click here(Click here)



Hide 75547B 4.REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

Z101186

HINT:

Perform the following procedure only when replacement of the No. 3 windshield outside moulding clip is necessary.



a.
B609595C01
1.302,0.99 0.99,0.646 false 6.51,0.375 6.688,0.313 false 0.833,1.083 0.99,1.281 0.156,0.198 10 false A 1.323,1.01 1.635,1.208 0.313,0.198 10 false *a 6.76,0.229 7.073,0.427 0.313,0.198 10 false *b 0.896,0.094 1.521,0.427 0.625,0.333 18 false i, ii 5.438,0.188 5.719,0.542 0.281,0.354 18 false iii
*a Tape *b Flange


i.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


ii.

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the No. 3 windshield outside moulding clips to drill off the No. 3 windshield outside moulding clip flanges, and remove the 4 No. 3 windshield outside moulding clips.

CAUTION:

Be careful of the drilled No. 3 windshield outside moulding clips, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

·

Prying the No. 3 windshield outside moulding clips with the drill may damage the No. 3 windshield outside moulding clip installation holes or drill bit.