Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (for Aero Type) › 2021.04–2021.07
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468081 FRONT BUMPER(for Aero Type) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(for Aero Type)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B599879N01
1.24,0.667 1.406,0.667 1.406,0.667 1.49,0.833 false 4.76,2.781 4.979,2.781 4.979,2.781 5.063,2.948 false 4.188,0.76 4.271,0.594 4.271,0.594 4.438,0.594 false 3.063,1.604 3.146,1.438 3.146,1.438 3.354,1.438 false 3.615,3.896 3.698,3.729 3.698,3.729 3.865,3.729 false 2.281,3.292 2.365,3.125 2.365,3.125 2.531,3.125 false 6.688,0.177 6.854,0.177 false 3.74,0.177 4.198,0.375 0.458,0.198 10 false x 7 5.573,3.396 6.031,3.594 0.458,0.198 10 false x 2 2,1.417 2.458,1.615 0.458,0.198 10 false x 2 2.448,3.875 2.906,4.073 0.458,0.198 10 false x 3 3.281,4.229 3.74,4.427 0.458,0.198 10 false x 3 2.115,3.677 2.573,3.875 0.458,0.198 10 false x 3 3.844,4.479 4.302,4.677 0.458,0.198 10 false x 3 3.25,3.167 3.708,3.365 0.458,0.198 10 false x 4 4.083,3.313 4.542,3.51 0.458,0.198 10 false x 4 5.854,0.063 6.802,0.417 0.948,0.354 18 false 1, 2 4.5,0.458 4.781,0.813 0.281,0.354 18 false 3 4.563,2.667 4.844,3.021 0.281,0.354 18 false 4 1.052,0.531 1.333,0.885 0.281,0.354 18 false 5 3.948,3.604 4.229,3.958 0.281,0.354 18 false 6 3.063,1.021 3.521,1.219 0.458,0.198 10 false x 3 4.938,2.313 5.396,2.51 0.458,0.198 10 false x 2 3.688,1.281 3.99,1.604 0.302,0.323 18 false 8 6.333,0.104 6.792,0.302 0.458,0.198 12 false (*A) 2.604,3.01 2.906,3.333 0.302,0.323 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CHANGE RADIATOR SHUTTER CONTROL STATE - (Click here) - -
3 UPPER RADIATOR SUPPORT SEAL 53292A - - -
4 FRONT FENDER MOULDING SUB-ASSEMBLY LH 75602A (Click here) - -
5 FRONT FENDER MOULDING SUB-ASSEMBLY RH 75601A (Click here) - -
6 ENGINE SIDE COVER SUB-ASSEMBLY LH 51044 - - -
7 ENGINE SIDE COVER SUB-ASSEMBLY RH 51043 - - -
8 FRONT BUMPER ASSEMBLY - (Click here) - -

*A w/ Grille Shutter - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front bumper assembly removal/installation are shown below.

Necessary Procedures after parts removed/installed/replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Front bumper assembly (Including removal and installation) Front television camera view adjustment Panoramic view monitor system (Click here)
·

Front television camera assembly (Including removal and installation)

·

Radiator grille (Including removal and installation)


Front television camera view adjustment Panoramic view monitor system (Click here)

HINT:
·

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.


·

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform ultrasonic sensor detection angle measurement.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

Carrying the front bumper assembly from the vehicle must be performed by 2 or more people.



Hide 2. CHANGE RADIATOR SHUTTER CONTROL STATE (w/ Grille Shutter)

Z101186

NOTICE:

In order to ensure safety, before performing troubleshooting or removing the radiator shutter assembly, change the grille shutter control mode to maintenance mode.

Click here(Click here)



Hide 53292A 3.REMOVE UPPER RADIATOR SUPPORT SEAL

a.
B592115


Hide 75602A 4.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH

a.
B592122C01
0.396,0.063 0.677,0.417 0.281,0.354 18 false i 4.635,1.219 4.771,1.385 0.135,0.167 10 true 1 4.781,0.875 4.917,1.042 0.135,0.167 10 true 2 5.125,0.698 5.26,0.865 0.135,0.167 10 true 3 5.448,0.656 5.583,0.823 0.135,0.167 10 true 4 5.74,0.615 5.875,0.781 0.135,0.167 10 true 5
V100135

Clip
V100136

Screw


i.

Remove the front fender moulding sub-assembly LH.

1. Put protective tape around the front fender moulding sub-assembly LH.

2. Using a 4 mm hexagon socket wrench, remove the screw.

3. Remove the 2 clips.

4. Insert a screwdriver with its tip wrapped with protective tape into the gap and detach the claw.

5. Using moulding remover B, detach the clip and disconnect the front fender moulding sub-assembly LH.

NOTICE:

Detach the clip one by one.




Hide 75601A 5.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

a.

Use the same procedure described for LH side.


Hide 51044 6.REMOVE ENGINE SIDE COVER SUB-ASSEMBLY LH

a.
B592121C01
0,0 0,0 false
V100135

Bolt
V100136

Screw



Hide 51043 7.REMOVE ENGINE SIDE COVER SUB-ASSEMBLY RH

a.

Use the same procedure described for LH side.


Hide 8.REMOVE FRONT BUMPER ASSEMBLY

a.
B592124C01
2.958,3.021 3.094,3.26 0.135,0.24 18 true i 0.167,0.094 0.427,0.375 0.26,0.281 18 true iii 0.146,4.104 0.417,4.354 0.271,0.25 18 true iv 0.146,2.031 0.333,2.313 0.188,0.281 18 true ii 5.354,2.01 5.542,2.292 0.188,0.281 18 true ii
V100135

Bolt
V100136

Screw
V100137

Clip - -


i.

Put protective tape around the front bumper assembly.


ii.

Remove the 2 clips.


iii.

Remove the 3 bolts.


iv.

Remove the 4 bolts and 4 screws and detach the clip.



b.
B600040C01
0.948,0.271 1.135,0.271 1.135,0.271 1.24,0.375 true 0.688,0.177 0.938,0.396 0.25,0.219 12 true *A 2.333,0.354 2.583,0.573 0.25,0.219 12 true *B 5.667,0.198 5.917,0.417 0.25,0.219 12 true *C 0.177,0.219 0.323,0.49 0.146,0.271 18 true i 2.573,0.302 2.719,0.573 0.146,0.271 18 true i 5.906,0.156 6.094,0.417 0.188,0.26 18 true ii
*A w/ Panoramic View Monitor System *B w/ Grille Shutter
*C w/ Headlight Cleaner System - -
V100135

Connector
V100136

Headlight Cleaner Hose


i.

Disconnect each connector.


ii.

w/ Headlight Cleaner System:

1. Detach the claw and disconnect the headlight cleaner hose.



c.
B617073C03
5.583,1.292 5.74,1.563 0.156,0.271 18 true i 4.26,0.99 4.417,1.26 0.156,0.271 18 true ii 2.719,0.667 2.833,0.844 0.115,0.177 10 true 1 2.552,0.521 2.667,0.698 0.115,0.177 10 true 2 2.385,0.396 2.5,0.573 0.115,0.177 10 true 3 1.74,0.75 1.896,1.021 0.156,0.271 18 true ii 2.698,0.365 2.854,0.635 0.156,0.271 18 true i
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2) - -


i.

Place your hand at the position shown in the illustration and pull in the direction of the arrow to detach the claws in the order shown in the illustration.


ii.

Place your hand at the position shown in the illustration and lift up in the direction of the arrow to detach the claw.



d.

Use the same procedure for the other side.


e.
B600041C01
0.052,0.031 0.292,0.333 0.24,0.302 18 true i
V113147

Remove in this Direction - -


i.

Detach the guide and claw and remove the front bumper assembly as shown in the illustration.