Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Rear) › 2021.04–2021.07
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468086 WHEEL OPENING MOULDING(for Rear) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Rear)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B613343N04
0.25,2.917 2.25,5.583 2,2.667 3.063,3.063 4.344,4.833 1.281,1.771 1.25,3.5 1.25,3.25 1.25,3.25 1.583,3.25 false 1.25,4.677 1.25,4.427 1.25,4.427 1.583,4.427 false 3.708,4.833 3.708,5.25 3.708,5.25 4.042,5.25 false 5.219,3.552 5.219,3.333 5.219,3.333 5.802,3.333 false 5.677,4.802 6.177,4.802 false 0.25,4.167 2.25,4.167 false 3.333,3.521 3.333,3.271 3.333,3.271 3.583,3.271 false 6.385,4.688 6.667,5.042 0.281,0.354 18 false 1 1.656,4.281 1.938,4.635 0.281,0.354 18 false 5 1.635,3.104 1.917,3.458 0.281,0.354 18 false 4 4.292,5.115 4.573,5.469 0.281,0.354 18 false 2 6.167,3.198 6.615,3.552 0.448,0.354 18 false 6 3.979,4.646 4.438,4.844 0.458,0.198 10 false x 3 0.292,2.948 0.698,3.292 0.406,0.344 12 false *A 0.281,4.198 0.625,4.594 0.344,0.396 12 false *B 6.021,3.24 6.469,3.594 0.448,0.354 10 false ● 3.813,3.156 4.26,3.51 0.448,0.354 10 false ● 3.938,3.104 4.219,3.458 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH 75606B (Click here) - -
2 REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH 75078 (Click here) - -
3 REAR DOOR NO. 1 MOULDING PAD - (Click here) - -
4 BODY ROCKER PANEL MOULDING ASSEMBLY LH 75860A - - -
5 STEP PLATE COVER LH 51774C - - -
6 QUARTER PANEL WHEEL OPENING MOULDING LH 75874 (Click here) - -

*A for Standard *B for Full Cover Type
● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75606B 1.REMOVE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH

a.
B610800C01
2.708,0.302 2.99,0.656 0.281,0.354 18 false i 5.26,0.875 5.417,1.146 0.156,0.271 18 true ii 0.552,1.958 0.833,2.313 0.281,0.354 18 true iv 4.052,1.979 4.24,2.26 0.188,0.281 18 true v 5.615,1.281 5.844,1.563 0.229,0.281 18 true iii 4.906,0.448 5.135,0.729 0.229,0.281 18 true iii 2.135,3.49 2.292,3.688 0.156,0.198 10 true 1 1.917,3.208 2.073,3.406 0.156,0.198 10 true 2 1.76,2.833 1.917,3.031 0.156,0.198 10 true 3 1.594,2.552 1.75,2.75 0.156,0.198 10 true 4 5.219,2.365 5.375,2.563 0.156,0.198 10 true 1 4.781,2.073 4.938,2.271 0.156,0.198 10 true 2 4.531,2.073 4.688,2.271 0.156,0.198 10 true 3
V113146

Place Hand Here
V113147

Remove in this Direction
V100135

Screw
V100136

Clip


i.

Put protective tape around the quarter outside moulding sub-assembly LH.


ii.

Using a 4 mm hexagon socket wrench, remove the screw.


iii.

Remove the 2 clips.


iv.

Place your hand at the positions shown in the illustration and detach the clip in the order shown in the illustration.


v.

Using moulding remover B, detach the clip in the order shown in the illustration and remove the quarter outside moulding sub-assembly LH as shown in the illustration.

NOTICE:

Detach the clip one by one.




Hide 75078 2.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Z101186

NOTICE:

When removing the rear door lower outside moulding sub-assembly LH, if the double-sided tape is difficult to remove, heat the adhesive of the rear door lower outside moulding sub-assembly LH using a heat light.



Standard Value:
Part Temperature
Rear Door Lower Outside Moulding Sub-assembly LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door lower outside moulding sub-assembly LH excessively.


a.
B613344C01
4.344,2.854 4.177,2.854 4.177,2.854 4.01,2.521 true 5.583,2.063 5.802,2.333 0.219,0.271 18 false iv 5.792,1.281 6.042,1.531 0.25,0.25 18 true ii 5.552,1.656 5.802,1.906 0.25,0.25 18 true iii 5.563,0.667 5.813,0.917 0.25,0.25 18 true iii 5.667,0.385 5.917,0.635 0.25,0.25 18 true iii 0.885,0.281 1.219,0.698 0.333,0.417 18 false i 4.385,2.427 4.542,2.625 0.156,0.198 10 true 1 3.865,2.313 4.021,2.51 0.156,0.198 10 true 2 3.573,2.583 3.729,2.781 0.156,0.198 10 true 3 3.865,2.969 4.021,3.167 0.156,0.198 10 true 4 3.781,3.208 3.938,3.406 0.156,0.198 10 true 5 3.635,2 3.854,2.271 0.219,0.271 18 true v 4.323,2.75 4.521,2.948 0.198,0.198 10 true *a
*a Double-sided Tape - -
V113147

Remove in this Direction
V100135

Screw
V100136

Clip - -


i.

Put protective tape around the rear door lower outside moulding sub-assembly LH.


ii.

Using a 4 mm hexagon socket wrench, remove the screw.


iii.

Remove the 3 clips.


iv.

Heat the adhesive of the rear door lower outside moulding sub-assembly LH using a heat light.


v.

Using moulding remover B, detach the clip and double-sided tape in the order shown in the illustration and remove the rear door lower outside moulding sub-assembly LH as shown in the illustration.

NOTICE:

Detach the clip one by one.




Hide 3.REMOVE REAR DOOR NO. 1 MOULDING PAD

Z101186

NOTICE:

When removing the rear door No. 1 moulding pad, if the double-sided tape is difficult to remove, heat the adhesive of the rear door No. 1 moulding pad using a heat light.



Standard Value:
Part Temperature
Rear Door No. 1 Moulding Pad 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door No. 1 moulding pad excessively.


a.
B613348N01
4.104,0.313 4.385,0.667 0.281,0.354 18 false i 1.729,0.031 2.01,0.385 0.281,0.354 18 false ii

i.

Heat the adhesive of the rear door No. 1 moulding pad using a heat light.


ii.

Remove the rear door No. 1 moulding pad.



Hide 75860A 4.REMOVE BODY ROCKER PANEL MOULDING ASSEMBLY LH (for Standard)

Hide 51774C 5.REMOVE STEP PLATE COVER LH (for Full Cover Type)

Hide 75874 6.REMOVE QUARTER PANEL WHEEL OPENING MOULDING LH

Z101186

NOTICE:

When removing the quarter panel wheel opening moulding LH, if the double-sided tape is difficult to remove, heat the adhesive of the quarter panel wheel opening moulding LH using a heat light.



Standard Value:
Part Temperature
Quarter Panel Wheel Opening Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the quarter panel wheel opening moulding LH.


a.
B610802C01
5.167,0.406 5.167,0.156 5.167,0.156 6.25,0.156 true 5.552,0.406 5.552,0.156 true 2.49,0.042 2.667,0.302 0.177,0.26 18 true i 1.458,0.844 1.625,1.125 0.167,0.281 18 true ii 1.531,1.479 1.792,1.76 0.26,0.281 18 true iii 4.219,0.042 4.438,0.323 0.219,0.281 18 true v 3.542,0.229 3.823,0.5 0.281,0.271 18 false iv 6.271,0.063 6.479,0.271 0.208,0.208 10 true *a
*a Double-sided Tape - -
V113147

Remove in this Direction
V100135

Screw
V100136

Grommet - -


i.

Using a clip remover with its tip wrapped with protective tape, detach the clip.


ii.

Remove the screw.


iii.

Push on the rear wheel house liner LH and use needle-nose pliers from the backside to remove the grommet.


iv.

Heat the adhesive of the quarter panel wheel opening moulding LH using a heat light.


v.

Detach the double-sided tape and remove the quarter panel wheel opening moulding LH as shown in the illustration.