Home › Vehicle Interior › SEAT BELT › OCCUPANT DETECTION SENSOR (for Power Seat)
RM38G0E _58 Vehicle Interior _100612 SEAT BELT _0468152 OCCUPANT DETECTION SENSOR(for Power Seat) A

SEAT BELT  OCCUPANT DETECTION SENSOR(for Power Seat)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B610968N01
0.115,0.521 7.063,3.76 6.948,3.24 6.333,0.25 6.75,0.25 false 5.885,3.198 5.885,3.448 5.885,3.448 6.052,3.448 false 1.448,3.354 2.281,3.354 2.281,3.354 2.365,3.125 false 1.292,1.635 1.677,1.635 false 3.167,0.51 3.167,0.24 3.167,0.24 3.573,0.24 false 6.063,0.094 6.344,0.448 0.281,0.354 18 false 1 1.219,3.229 1.5,3.583 0.281,0.354 18 false 3 1.094,1.51 1.375,1.865 0.281,0.354 18 false 4 6.396,3.344 6.677,3.698 0.281,0.354 18 false 5 3.667,0.125 3.948,0.479 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 FRONT SEAT ASSEMBLY RH - - - -
3 FRONT SEAT FRONT CUSHION SHIELD RH 71867W (Click here) - -
4 FRONT SEAT CUSHION SHIELD RH 71811T (Click here) - -
5 FRONT SEAT INNER CUSHION SHIELD RH 71861K (Click here) - -

B610969N01
0.156,0.083 7.042,2.094 6.885,2.01 4.052,0.135 6.99,1.99 2.938,1.854 6.063,3.094 5.729,3.094 5.729,3.094 5.563,3.094 false 2.917,4.292 3.417,4.292 false 3.542,2.094 3.542,2.458 3.542,2.458 3.75,2.458 false 1.635,1.542 1.25,1.542 false 1.208,0.656 1.677,0.656 false 5.917,0.771 6.344,0.771 false 1.094,1.417 1.646,1.771 0.552,0.354 18 false 9 3.781,2.313 4.333,2.667 0.552,0.354 18 false 8 3.438,4.167 3.99,4.521 0.552,0.354 18 false 6 6.052,2.969 6.604,3.323 0.552,0.354 18 false 7 6.083,4.146 6.542,4.344 0.458,0.198 10 false x 4 0.979,0.573 1.292,0.771 0.313,0.198 10 false ●*1 6.563,0.688 6.719,0.885 0.156,0.198 10 false ● 1.01,1.458 1.167,1.656 0.156,0.198 10 false ● 6.677,0.635 7.031,0.958 0.354,0.323 18 false 10 4.135,0.208 4.51,0.448 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

6 WIRING HARNESS SUPPORT 82712L - - -
7 FRONT SEATBACK ASSEMBLY RH - - - -
8 SEAT CUSHION COVER WITH PAD - - - -
9 FRONT SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR) 71511A (Click here) - -
10 FRONT SEAT CUSHION HEATER ASSEMBLY RH 87511C (Click here) - -

*A w/ Seat Heater System - -
*1 FRONT SEAT CUSHION COVER SUB-ASSEMBLY RH - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
B543257


·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering ilghts Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read precautionary notices concerning the SRS airbag system before servicing.

(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

(Click here)



Hide 2.REMOVE FRONT SEAT ASSEMBLY RH

a.

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL


Hide 71867W 3.REMOVE FRONT SEAT FRONT CUSHION SHIELD RH

Z101186

·

Use the same procedure described for the LH side.

(Click here)



Hide 71811T 4.REMOVE FRONT SEAT CUSHION SHIELD RH

Z101186

(Click here)

Hide 71861K 5.REMOVE FRONT SEAT INNER CUSHION SHIELD RH

Z101186

·

Use the same procedure described for the LH side.

(Click here)



Hide 82712L 6.REMOVE WIRING HARNESS SUPPORT

a.

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Hide 7.REMOVE FRONT SEATBACK ASSEMBLY RH

a.

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Hide 8.REMOVE SEAT CUSHION COVER WITH PAD

a.

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Hide 71511A 9.REMOVE FRONT SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR)

Z101186

NOTICE:

Be careful not to dirty or damage the front seat cushion cover sub-assembly RH and the front seat cushion pad RH (occupant detection sensor).



a.
B610957C01
0.49,0.125 0.771,0.479 0.281,0.354 18 false i

i.

Using a thin-bladed screwdriver, detach the claw to remove the front seat cushion cover sub-assembly RH from the front seat cushion pad RH (occupant detection sensor) as shown in the illustration.

HINT:

Tape the thin-bladed screwdriver tip before use.




Hide 87511C 10.REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)

Z101186

·

Use the same procedure described for the LH side.

Click here(Click here)