Home › Vehicle Interior › SEAT BELT › FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat)
RM38G0E _58 Vehicle Interior _100612 SEAT BELT _0468153 FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat) A

SEAT BELT  FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B610944N01
0.75,0.083 3.833,1.583 3.083,1.5 0.333,1.667 3.25,3 2.917,1.333 3.167,1.083 3.167,1.25 3.167,1.25 3.417,1.25 false 1.094,1.917 1.333,1.917 1.333,1.917 1.479,2.073 false 1.99,2.198 2.167,2 2.167,2 2.583,2 false 2.646,0.563 2.833,0.333 2.833,0.333 3.25,0.333 false 5.5,1.917 6.167,1.917 false 6.25,0.25 6.583,0.25 false 0.417,1.75 0.792,1.99 0.375,0.24 12 false *B 0.833,0.167 1.208,0.406 0.375,0.24 12 false *A 3.469,1.198 3.781,1.396 0.313,0.198 10 false *1 0.917,1.833 1.229,2.031 0.313,0.198 10 false *1 2.635,1.896 2.917,2.25 0.281,0.354 18 false 4 3.302,0.229 3.583,0.583 0.281,0.354 18 false 3 6.083,0.146 6.365,0.5 0.281,0.354 18 false 1 6.219,1.813 6.5,2.167 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 FRONT SEAT ASSEMBLY LH - - - -
3 FRONT SEAT BELT SET LH 73204A - - -
4 FRONT SEAT BELT SET RH 73203 - - -

*A for Driver Side *B for Front Passenger Side
*1 FRONT SEAT BELT ANCHOR PLATE - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
B543257


·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering ilghts Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read precautionary notices concerning the SRS airbag system before servicing.

(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

(Click here)



Hide 73204A 3.REMOVE FRONT SEAT BELT SET LH (for Driver Side)

a.
B609764


Hide 73203 4.REMOVE FRONT SEAT BELT SET RH (for Front Passenger Side)

a.
B609765C02
0,0 0,0 false
V100135

Band
V100136

Connector
V100137

Nut - -