| *A | for Driver Side | *B | for Front Passenger Side |
| *C | w/ Courtesy Light | *D | w/ Reflex Reflector Assembly |
| *E | w/ Cover | - | - |
| *A | w/ Double Locking System | *B | w/o Double Locking System |
| *C | for Driver Side | - | - |
| *1 | HOLE PLUG | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front door removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
1. PRECAUTION
|
|
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
|
|
for 1GR-FE
for V35A-FTS
3.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
4.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
67923E 10.REMOVE NO. 1 FRONT DOOR STIFFENER CUSHION
68172A 13.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
68151E 16.REMOVE FRONT DOOR GLASS RUN
67404F 17.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
69032 20.REMOVE DOOR LOCK COVER SET
|
Remove in this Direction | - | - |
69040A 21.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
w/o Double Locking System:
|
Connector |
|
Screw |
|
Remove in this Direction | - | - |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 screws and front door lock with motor assembly.
Remove the front door lock with motor assembly as shown in the illustration.
w/ Double Locking System:
|
Connector |
|
Screw |
|
Remove in this Direction | - | - |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 screws and front door lock with motor assembly.
Remove the front door lock with motor assembly as shown in the illustration.
69318C 22.REMOVE DOOR LOCK WIRING HARNESS SEAL
|
|
w/o Double Locking System:
w/ Double Locking System:
69036A 23.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY
w/o Double Locking System:
|
Remove in this Direction | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.
Disengage the claws to remove the front door lock cover sub-assembly.
w/ Double Locking System:
|
Remove in this Direction | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.
Disengage the claws to remove the front door lock cover sub-assembly.
69720D 24.REMOVE OPEN LEVER FRONT DOOR LOCK REMOTE CONTROL CABLE
w/o Double Locking System:
|
Remove in this Direction | - | - |
Disengage the guide to remove the open lever front door lock remote control cable from the front door lock with motor assembly.
w/ Double Locking System:
|
Remove in this Direction | - | - |
Disengage the guide to remove the open lever front door lock remote control cable from the front door lock with motor assembly.
69760B 25.REMOVE FRONT DOOR INSIDE LOCK AND UNLOCK KNOB LOCKING CABLE
w/o Double Locking System:
|
Remove in this Direction | - | - |
Disengage the guide to remove the front door inside lock and unlock knob locking cable from the front door lock with motor assembly.
w/ Double Locking System:
|
Remove in this Direction | - | - |
Disengage the guide to remove the front door inside lock and unlock knob locking cable from the front door lock with motor assembly.