| *A | w/ Courtesy Light | *B | w/ Reflex Reflector Assembly |
| *C | w/ Cover | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 10 | REAR DOOR GLASS INNER WEATHERSTRIP | 68174A | - | - | - |
| 11 | REAR DOOR SERVICE HOLE COVER | 67842E | ( ) |
- | - |
| ● | Non-reusable part | - | - |
| *A | w/ Double Locking System | *B | w/o Double Locking System |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front door removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
1. PRECAUTION
|
|
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
|
|
for 1GR-FE
for V35A-FTS
67604 8.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
68174A 10.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP
68152C 12.REMOVE REAR DOOR GLASS RUN
69038A 16.REMOVE DOOR LOCK COVER SET
|
Remove in this Direction | - | - |
69060A 17.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
w/o Double Locking System:
|
Connector |
|
Screw |
|
Remove in this Direction | - | - |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the screws.
Move the rear door lock with motor assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove rear door lock with motor assembly.
w/ Double Locking System:
|
Connector |
|
Screw |
|
Remove in this Direction | - | - |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the screws.
Move the rear door lock with motor assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.
69318D 18.REMOVE DOOR LOCK WIRING HARNESS SEAL
|
|
w/o Double Locking System:
w/ Double Locking System:
69038A 19.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY
w/o Double Locking System:
|
Remove in this Direction | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.
Disengage the claws to remove the rear door lock cover sub-assembly.
w/ Double Locking System:
|
Remove in this Direction | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.
Disengage the claws to remove the rear door lock cover sub-assembly.
69740E 20.REMOVE REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE
w/o Double Locking System:
|
Remove in this Direction | - | - |
Disengage the guide to remove the rear door lock remote control cable assembly from the rear door lock with motor assembly.
w/ Double Locking System:
|
Remove in this Direction | - | - |
Disengage the guide to remove the rear door lock remote control cable assembly from the rear door lock with motor assembly.
69780E 21.REMOVE REAR DOOR LOCK AND UNLOCK KNOB INSIDE LOCKING CABLE
w/o Double Locking System:
|
Remove in this Direction | - | - |
Disengage the guide to remove the rear door inside locking cable assembly from the rear door lock with motor assembly.
w/o Double Locking System:
|
Remove in this Direction | - | - |
Disengage the guide to remove the rear door inside locking cable assembly from the rear door lock with motor assembly.