| *a | Centering Bolt |
| *b | Standard Bolt |
Centering bolts are used to install the door hinges to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.
The specified torque for standard bolts is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
1.INSPECT BACK DOOR
Check that the clearance measurements of areas A to L are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 8.9 to 11.9 mm (0.3504 to 0.4685 in.) |
B | 0.1 to 3.1 mm (0.0039 to 0.1220 in.) |
| C | 12.8 mm (0.5039 in.) |
D | -0.2 mm (-0.0079 in.) |
| E | 2.35 to 8.35 mm (0.0925 to 0.3287 in.) |
F | 4.95 to 10.95 mm (0.1949 to 0.4311 in.) |
| G | 3.0 to 8.0 mm (0.1181 to 0.3150 in.) |
H | -2.6 to 2.4 mm (-0.1024 to 0.0945 in.) |
| I | 2.85 to 7.85 mm (0.1122 to 0.3091 in.) |
J | -1.35 to 3.35 mm (-0.0531 to 0.1319 in.) |
| K | 2.85 to 7.85 mm (0.1122 to 0.3091 in.) |
L | 3.85 to 9.85 mm (0.1516 to 0.3878 in.) |
66310P 2.REMOVE ROPE HOOK ASSEMBLY (w/o Rear No. 2 Seat)
64716P 3.REMOVE DECK TRIM COVER (w/o Rear No. 2 Seat)
58410B 4.REMOVE DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
58418H 5.REMOVE REAR FLOOR BOARD REAR LH (w/o Rear No. 2 Seat)
58417B 6.REMOVE REAR FLOOR BOARD REAR RH (w/o Rear No. 2 Seat)
Use the same procedure described for the LH side.
64993 7.REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
58574G 8.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
58410B 9.REMOVE DECK BOARD ASSEMBLY (w/ Rear No. 2 Seat)
66310P 10.REMOVE ROPE HOOK ASSEMBLY (w/ Rear No. 2 Seat)
58418H 11.REMOVE REAR FLOOR BOARD REAR LH (w/ Rear No. 2 Seat)
58417B 12.REMOVE REAR FLOOR BOARD REAR RH (w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
58574G 13.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/ Rear No. 2 Seat)
14.ADJUST BACK DOOR
Loosen the 4 hinge bolts on the back door and adjust the back door position.
Tighten the 4 hinge bolts on the vehicle body after adjustment.
Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.
Using a brass bar and a hammer, hit the striker to adjust its position.
Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.
58574G 15.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/ Rear No. 2 Seat)
58418H 16.INSTALL REAR FLOOR BOARD REAR LH (w/ Rear No. 2 Seat)
58417B 17.INSTALL REAR FLOOR BOARD REAR RH (w/ Rear No. 2 Seat)
66310P 18.INSTALL ROPE HOOK ASSEMBLY (w/ Rear No. 2 Seat)
58410B 19.INSTALL DECK BOARD ASSEMBLY (w/ Rear No. 2 Seat)
58574G 20.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
64993 21.INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
58418H 22.INSTALL REAR FLOOR BOARD REAR LH (w/o Rear No. 2 Seat)
58417B 23.INSTALL REAR FLOOR BOARD REAR RH (w/o Rear No. 2 Seat)
58410B 24.INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
64716P 25.INSTALL DECK TRIM COVER (w/o Rear No. 2 Seat)
66310P 26.INSTALL ROPE HOOK ASSEMBLY (w/o Rear No. 2 Seat)