| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | FRONT SEAT CUSHION HEATER ASSEMBLY LH | 87511D | ( ) |
- | - |
| 2 | FRONT SEAT CUSHION COVER SUB-ASSEMBLY LH | 71072 | ( ) |
- | - |
| 3 | SEAT CUSHION COVER WITH PAD | - | - | - | - |
| *1 | FRONT SEAT CUSHION PAD LH | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 4 | FRONT SEATBACK ASSEMBLY LH | - | - | - | - |
| 5 | WIRING HARNESS SUPPORT | 82712L | - | - | - |
| *A | w/o Rear Seat Entertainment System | *B | w/ Rear Seat Entertainment System |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, in.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 6 | FRONT SEAT INNER CUSHION SHIELD LH | 71862K | - | - | - |
| 7 | FRONT SEAT CUSHION SHIELD RH | 71811T | - | - | - |
| 8 | FRONT SEAT CUSHION SHIELD LH | 71812T | - | - | - |
| 9 | FRONT SEAT FRONT CUSHION SHIELD LH | 71867X | - | - | - |
| 10 | FRONT SEAT ASSEMBLY LH | - | - | - | - |
| *A | for Driver Side | *B | for Front Passenger Side |
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
87511D 1.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH
| *a | Area A | *b | Area B |
| *c | Area C | *d | Area D |
| *e | Area E | *f | Bridge part |
| *g | Positioning Standard | - | - |
The following procedure is performed to install the front seat cushion heater assembly LH to front seat cushion pad LH.
1. Remove the release paper of area A from the front seat cushion heater assembly LH and attach it to the front seat cushion pad LH aligning with the positioning standard.
2. Remove the release paper of area B from the front seat cushion heater assembly LH and attach it to the front seat cushion pad LH aligning with the positioning standard.
3. Remove the release paper of area C from the front seat cushion heater assembly LH and attach it to the front seat cushion pad LH aligning with the positioning standard.
4. Remove the release paper of area D from the front seat cushion heater assembly LH and attach it to the front seat cushion pad LH aligning with the positioning standard.
5. Remove the release paper of area E from the front seat cushion heater assembly LH and attach it to the front seat cushion pad LH aligning with the positioning standard.
6. Insert 6 bridge parts of the front seat cushion heater assembly LH into the groove of the front seat cushion pad LH.
After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.
Do not reuse the front seat cushion heater assembly LH and front seat cushion pad LH/
Apply pressure to paste the front seat cushion heater assembly LH to the front seat cushion pad LH securely.
3.INSTALL SEAT CUSHION COVER WITH PAD
4.INSTALL FRONT SEATBACK ASSEMBLY LH
82712L 5.INSTALL WIRING HARNESS SUPPORT
71862K 6.INSTALL FRONT SEAT INNER CUSHION SHIELD LH
71811T 7.INSTALL FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)
71812T 8.INSTALL FRONT SEAT CUSHION SHIELD LH (for Driver Side)
71867X 9.INSTALL FRONT SEAT FRONT CUSHION SHIELD LH
10.INSTALL FRONT SEAT ASSEMBLY LH