| *A | w/ Climate Control Seat System | *B | w/ Wire Harness |
| *1 | NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY LH | *2 | SPRING NUT |
| *3 | PLATE WASHER | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
| ● | Non-reusable part | - | - |
| *A | w/ Seat Heater System | *B | w/ Rear Seat Side Airbag |
| *C | w/ Child Restraint System Guide | *D | w/o Child Restraint System Guide |
| *1 | REAR NO. 1 SEAT CUSHION PAD LH | *2 | NO. 1 SEATBACK PAD LH |
| *3 | HOG RING | *4 | RIVET |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| *A | w/o Wire Harness | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
1.INSTALL REAR SEAT CUSHION PAD B (w/ Climate Control Seat System)
85860F 2.INSTALL NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH (w/ Climate Control Seat System)
Temporarily install the No. 1 seat cushion climate control blower assembly LH to the No. 1 seat cushion frame sub-assembly LH.
Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new φ 4 mm rivet into the nose piece.
Press the rivets perpendicularly to the installation holes. Using the air riveter, install the No. 1 seat cushion climate control blower assembly LH with the rivets.
When installing the rivets to the panel surface, do not tilt the riveter.
Do not leave a gap between the rivet head portion and the panel.
Pull the trigger again to cut off the rivet if it is not cut off.
Attach the claw.
82194 3.INSTALL REAR SEAT WIRE LH (w/ Wire Harness)
78910D 4.INSTALL SEAT FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH
72580E 5.INSTALL RECLINING ADJUSTING CABLE ASSEMBLY LH
72660P 6.INSTALL REAR SEAT LOCK ASSEMBLY LH
72650J 7.INSTALL REAR SEAT LOCK ASSEMBLY RH
72144 8.INSTALL REAR LOWER REAR SEAT TRACK BRACKET LH
71461H 9.INSTALL REAR SEAT CUSHION SPRING
85867E 10.INSTALL NO. 1 SEAT SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)
Temporarily install the No. 1 seat seatback climate control blower LH to the No. 1 seatback frame sub-assembly LH.
Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new φ 4 mm rivet into the nose piece.
Press the rivets perpendicularly to the installation holes. Using the air riveter, install the No. 1 seat seatback climate control blower LH with the rivets.
When installing the rivets to the panel surface, do not tilt the riveter.
Do not leave a gap between the rivet head portion and the panel.
Pull the trigger again to cut off the rivet if it is not cut off.
Attach the claw.
72308C 11.INSTALL NO. 1 RECLINING CONTROL LINK SUB-ASSEMBLY LH
79104A 12.INSTALL NO. 1 SEATBACK FRAME SUB-ASSEMBLY LH
| *a | Cable End | - | - |
|
Install in this Direction | - | - |
Temporarily install the No. 1 seatback frame sub-assembly LH with the 4 bolts.
While pushing in the direction shown in the illustration, install the No. 1 seatback frame sub-assembly LH with the 4 bolts in the order shown in the illustration.
Turn each cable end in the installation direction shown in the illustration and connect each cable end.
Attach each casing cap.
72551R 13.INSTALL SEAT RECLINING HINGE COVER LH
72552P 14.INSTALL SEAT RECLINING HINGE COVER LH
71H75R 15.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER LH
71H76N 16.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER LH
79117D 17.INSTALL NO. 1 SEAT CUSHION CARPET (w/ Child Restraint System Guide)
| *1 | No. 1 Seatback Frame Sub-assembly LH | - | - |
| *a | Fastener | - | - |
|
Install in this Direction | - | - |
Follow the procedure below to install the No. 1 seat cushion carpet.
1. Pass the slit part of the No. 1 seat cushion carpet through the wire part of No. 1 seatback frame sub-assembly LH.
2. Wrap the No. 1 seat cushion carpet around the pipe of the No. 1 seatback frame sub-assembly LH and attach it with a fastener as shown in the illustration.
79014B 19.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY LH
20.INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH
71930Q 21.INSTALL REAR SEAT HEADREST SUPPORT ASSEMBLY
71076F 26.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY LH
27.INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH
71702D 28.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH
72996H 29.INSTALL REAR SEATBACK COVER (w/ Child Restraint System Guide)
87501F 30.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)
73390C 31.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
72928E 32.INSTALL REAR SEAT CUSHION UNDER COVER LH
|
Screw A |
|
Screw B |
|
Screw C | - | - |
Install the rear seat cushion under cover LH with the screw A.
Install the screw B.
Install the 7 screws C.
Attach the J hook of the No. 1 seat cushion cover sub-assembly LH.
72998D 33.INSTALL REAR SEAT CUSHION COVER LH
71301H 34.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
71302G 35.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
82194 36.INSTALL REAR SEAT WIRE LH (w/o Wire Harness)
79967X 37.INSTALL REAR NO. 1 SEAT NO. 5 LEG SIDE COVER
79967W 38.INSTALL REAR NO. 1 SEAT NO. 4 LEG SIDE COVER
79951B 39.INSTALL NO. 1 SEAT NO. 1 CUSHION COVER
79952A 40.INSTALL NO. 1 SEAT NO. 2 CUSHION COVER
76971G 41.INSTALL REAR UNDER COVER
78950F 42.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
71834X 43.INSTALL REAR NO. 2 SEAT RECLINING COVER LH
72526L 44.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
|
Pushed Place |
|
Push in this Direction |
While pressing the reclining adjuster release handle LH as shown in the illustration, install the reclining adjuster release handle LH with the screw.
72329G 45.INSTALL REAR NO. 2 SEAT ADJUSTER BOLT COVER
71833V 46.INSTALL NO. 1 SEAT NO. 2 RECLINING COVER RH