| *A | w/ Child Restraint System Guide | - | - |
| *1 | NO. 1 SEATBACK PAD RH | *2 | HOG RING |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 23 | REAR NO. 1 SEAT ASSEMBLY RH | - | - | - | - |
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
87530A 1.INSTALL REAR NO. 1 SEATBACK HEATER ASSEMBLY RH
| *a | A Area | *b | B Area |
| *c | C Area | *d | Bridge Area |
| *e | Matchmark | - | - |
Follow the steps below to install the rear No. 1 seatback heater assembly RH to the No. 1 seatback pad RH.
1. Remove the peeling paper on the A area and paste the A area of rear No. 1 seatback heater assembly RH to the No. 1 seatback pad RH as the matchmark.
2. Remove the peeling paper on the B area and paste the B area of rear No. 1 seatback heater assembly RH to the No. 1 seatback pad RH as the matchmark.
3. Remove the peeling paper on the C area and paste the C area of rear No. 1 seatback heater assembly RH to the No. 1 seatback pad RH as the matchmark.
4. Insert the bridge area to the groove of No. 1 seatback pad LH.
After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.
Do not reuse the rear No. 1 seatback heater assembly RH and No. 1 seatback pad RH.
Apply pressure to paste the rear No. 1 seatback heater assembly RH to the No. 1 seatback pad RH securely.
3.INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH
71930Q 4.INSTALL REAR SEAT HEADREST SUPPORT ASSEMBLY
73373 5.INSTALL REAR SEAT SHOULDER BELT COVER
73178A 6.INSTALL SEAT BELT ANCHOR COVER CAP
71701A 7.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH
72996H 8.INSTALL REAR SEATBACK COVER (w/ Child Restraint System Guide)
73310D 9.CONNECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY (SEAT ANCHOR)
72995F 12.INSTALL REAR SEAT CUSHION COVER RH
71301G 13.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
71302C 14.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
79967W 15.INSTALL REAR NO. 1 SEAT NO. 4 LEG SIDE COVER
79951B 16.INSTALL NO. 1 SEAT NO. 1 CUSHION COVER
79952A 17.INSTALL NO. 1 SEAT NO. 2 CUSHION COVER
78950F 18.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
71833S 19.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
72329F 21.INSTALL REAR SEAT ADJUSTER BOLT COVER
71834S 22.INSTALL REAR NO. 1 SEAT RECLINING COVER LH
23.INSTALL REAR NO. 1 SEAT ASSEMBLY RH