| *A | w/ Child Restraint System Guide | *B | w/o Child Restraint System Guide |
| *1 | NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY RH | *2 | HOG RING |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 21 | REAR NO. 1 SEAT ASSEMBLY RH | - | - | - | - |
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
87510Z 1.INSTALL REAR NO. 1 SEAT CUSHION HEATER ASSEMBLY RH
| *a | A Area | *b | B Area |
| *c | C Area | *d | D Area |
| *e | E Area | *f | Bridge Area |
| *g | Matchmark | - | - |
Follow the steps below to install the rear No. 1 seat cushin heater assembly RH to the rear No. 1 seat cushion pad RH.
1. Remove the peeling paper on the A area and paste the A area of rear No. 1 seat cushion heater assembly RH to the rear No. 1 seat cushion pad RH as the matchmark.
2. Remove the peeling paper on the B area and paste the B area of rear No. 1 seat cushion heater assembly RH to the rear No. 1 seat cushion pad RH as the matchmark.
3. Remove the peeling paper on the C area and paste the C area of rear No. 1 seat cushion heater assembly RH to the rear No. 1 seat cushion pad RH as the matchmark.
4. Remove the peeling paper on the D area and paste the D area of rear No. 1 seat cushion heater assembly RH to the rear No. 1 seat cushion pad RH as the matchmark.
5. Remove the peeling paper on the E area and paste the E area of rear No. 1 seat cushion heater assembly RH to the rear No. 1 seat cushion pad RH as the matchmark.
6. Insert the bridge area to the groove of rear No. 1 seat cushion pad RH.
After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.
Do not reuse the rear No. 1 seat cushion heater assembly RH and rear No. 1 seat cushion pad RH.
Apply pressure to paste the rear No. 1 seat cushion heater assembly RH to the rear No. 1 seat cushion pad RH securely.
3.INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH
71701A 4.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH
72996H 5.INSTALL REAR SEATBACK COVER (w/ Child Restraint System Guide)
73310D 6.CONNECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY (SEAT ANCHOR)
73350 8.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
72995F 10.INSTALL REAR SEAT CUSHION COVER RH
71301G 11.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
71302C 12.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
79967W 13.INSTALL REAR NO. 1 SEAT NO. 4 LEG SIDE COVER
79951B 14.INSTALL NO. 1 SEAT NO. 1 CUSHION COVER
79952A 15.INSTALL NO. 1 SEAT NO. 2 CUSHION COVER
78950F 16.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
71833S 17.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
72329F 19.INSTALL REAR SEAT ADJUSTER BOLT COVER
71834S 20.INSTALL REAR NO. 1 SEAT RECLINING COVER LH
21.INSTALL REAR NO. 1 SEAT ASSEMBLY RH